13.8V 8A power supply with 12V lead acid battery charger (UPS function)

DIN-rail modular 40A 230V 2P contactor with 230Vac coil with only 1.6W coil power.

DIN-rail modular 25A 230V 2P contactor with 230Vac coil with only 1.2W coil power.

Can be used with DomBus23 and DomBus31 domotic modules.
It can also be controlled by DomBusTH and DomBus12 through the DomRelay2 module.

DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).

Connect more I/O and sensors to Domoticz using Creasol DomESP2.

Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).

This is a package with 3x relay modules DomRelay2 (3pcs)

Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.

Contacts are protected from overcurrent and overvoltage.

Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.

Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.

Contacts are protected from overcurrent and overvoltage.

Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.

WiFicontroller ESP8266 original WeMos D1 Mini, 4MB flash. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz or other controllers, by HTTP and MQTT. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

Completed with pin header, male and female, provided apart (to be soldered, if needed)

Case for Raspberry PI 4, official case.

Starter kit for your home automation system!

Content:

• 1x Raspberry PI4 genuine (without case)
• 1x 32gb high-endurance microSD already programmed with Raspbian + Domoticz + Firewall + Backup
• 1x RS485-to-USB adapter
• 1x Creasol DomBus1 (2 relay outputs, 6 inputs, 1 AC input)
• 1x Creasol DomBusTH (temperature+relative humidity sensor, white+red+green leds, 4 inputs, 2 outputs, 1 analog input)

USB cable, 1m long, with switch.
Type-A male USB connector on one side, Type-C male USB connector on the other side.

Suitable for Raspberry PI 4 , modern smartphones and other devices.

Compact power supply with EU plug, 5V 3000mA, optimal for Raspberry PI 4 and for fast battery charging.

Output voltage: 5V

Output current: 3A.

EU plug.

No USB cable.

Long range 433.92 MHz remote control duplicator, in light-weight soft-touch shell

Original SanDisk microSDHC memory, High Endurance, 64GB, U3 V30 Class10 40MB/s write speed, 100MB/s read speed.

Already programmed with Raspbian and Domoticz, suitable for Raspberry PI3, Raspberry PI4, Rock PI S.

Original SanDisk microSDHC memory, High Endurance, 64GB, U3 V30 Class10 40MB/s write speed, 100MB/s read speed.
Supplied with SD adapter.

Suitable for Raspberry PI4 (high endurance type, with longer life in respect to normal cards), Rock PI S and video surveillance.

People who need to burn a Raspbian image optimized for a longer life of MicroSd card, can check the URL http://www.creasol.it/support/domotics-home-automation-and-diy/132-installing-domoticz-on-raspberry-raspbian

Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.

Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.

Can be used to measure level of water or other liquid inside a tank, for example.

Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.

AVAILABLE ONLY AS domKit1 AND domKit2!

Raspberry PI 4 Single Board Computer, Model B, 2GB RAM.

Professional 100m flex cable for RS485 (and Modbus) serial bus. 4 wires + shield: 2*0.22mm twisted (120 ohm impedance, for data) + 2*0.5mm (for supply) + shielding. External diameter 5.5mm.

The ideal cable to connect Creasol DomBus I/O expanders to Domoticz home automation controller.

Connect more I/O and sensors to Domoticz using Creasol DomESP1.

Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

Also the DomESP2 board is available, using plugin terminal blocks!

Coaxial cable for alarm system, 4x0,22mm², 100m

Cavo coassiale per antifurto, 4x0.22mmq, 4 fili da 0,22mmq, matassa 100m.

NOT AVAILABLE

Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz

1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC

+/- 0.5K accuracy, 9-12bit resolution.

Suitable for Domoticz/RaspberryPI and ESP8266 controllers

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

Compact switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 0.85 to 12Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 18x10x4mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

With 3 digits display showing the input and output voltage.

Size: 61x34x12mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 48x23x14mm

High performance filtered antenna with stainless steel wall mount bracket, with 3m coax cable RG58 and male-SMA connector.

3m coax cable, RG58, and SMA male connector. Suitable for RFXCOM and other transmitter, receivers, transceivers operating at 433MHz, 434MHz or 435MHz.

2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz

Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.

Very high quality, long life, made in Italy.

Universal multi-frequency receiver with 2 outputs, 60V 50mA load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz. Also, it can be programmed to work in 2 frequency simultaneously.

Multifrequency remote control duplicator, in plastic case with soft touch feeling, available in 6 colors.

Automatically learn frequency and code of original remote controls, transmitting at 433.92MHz, 868.3MHz and from 220 to 418 MHz (not for EU version, where these frequencies are disabled).

Very easy to program, each button is indepent and can work in a different frequency.

Alkaline battery for remote controls, 12V 60mAh. 27x10mm. Used in several remote controls, but NOT USED in creasol remote controls!

Standard antenna with stainless steel wall mount bracket.

2.1dB gain, 15MHz bandwidth, from 860 to 880 MHz

Very high quality, long life, made in Italy.

High performance filtered antenna with stainless steel wall mount bracket.

2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz

Very high quality, long life, made in Italy.

Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.

Standard antenna with stainless steel wall mount bracket.

2.1dB gain, 15MHz bandwidth, from 425 to 440 MHz

Very high quality, long life, made in Italy.

Optional memory for universal receivers like UniRec2.

It can be installed in the receiver to supports a greater number of different remote controls.

As remote control manufacturers, we have the knowledge to repair faulty remote controls.

We provide the remote control repairs service for a fixed price.