Universal remote control duplicator, which is able to copy up to 4 different remote controls which transmit at 433.92 MHz.
Four buttons, very easy programming, strong, nice look, very long range!

Remote control duplicator that is able to copy up to 4 remote controls which transmit in these frequencies: 433.92, 868.3, 315, 403.55, 418, 286-360, 384-400 MHz.
Four buttons, automatic frequency detection, very easy programming, nice look!
Can operate in different frequencies (one for each button).

Multifrequency remote control duplicator, in plastic case with soft touch feeling, available in 6 colors.

Automatically learn frequency and code of original remote controls, transmitting at 433.92MHz, 868.3MHz and from 220 to 418 MHz (not for EU version, where these frequencies are disabled).

Very easy to program, each button is indepent and can work in a different frequency.

Long range 433.92 MHz remote control duplicator, in light-weight soft-touch shell

Multifrequency micro receiver, 1 channel, operating at 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315, 403.55, 418 MHz. Can be used to replace a non-working receiver, or to control an existing electronic board by almost any remote control in the market, both fixed and rolling code, AM and FM.
The receiving frequency and modulation can be programmed by the user: also, it's possible to program 2 different frequencies, even with different modulation, to manage remote controls transmitting in 2 different frequencies/modulations: for example the receiver can be used by a set of 433.92MHz OOK and 868.8MHz FSK remote controls.

Alkaline battery for remote controls, 12V 60mAh. 27x10mm. Used in several remote controls, but NOT USED in creasol remote controls!

Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).

Creasol DomBus12 is a compact module, 40x30x11mm, with 9 configurable inputs/outputs.
It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus12 is designed to consume low power, be reliable, fully configurable and easy to use.

Multifrequency long-range remote control duplicator which should be connected, by a pushbutton, to an external power supply. Can be used inside a car, to open gate/door, by flashing highbeam lights or brake pedal.
Copy up to 4 fixed-code remote controls, even in different frequencies.

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

Connect more I/O and sensors to Domoticz using Creasol DomESP1.

Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

Also the DomESP2 board is available, using plugin terminal blocks!

Universal multi-frequency receiver with 2 relay outputs and 250V 5A load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz.

WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

AVAILABLE ONLY AS domKit1 AND domKit2!

Raspberry PI 4 Single Board Computer, Model B, 2GB RAM.

Creasol DomBus31 is a din-rail relay module, 115x90x40mm, with 8 relays outputs. 6 relays are SPST (Normally Open outputs) with 250V 5A max capability, and 2 relays are SPDT (Normally Open and Normally Closed outputs) with 10A capability. It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus31 provides excellent performance in terms of power optimization: with all 8 relays active (the worst case), the power consumption is only 500mW! As a comparison, KMTronic 8 relays module consumes 12W, Denkovi 8 relays board consumes about 3W, Sonoff Dual R2 consumes 2W with only 2 relays enabled.

Suitable to be used as Domoticz relays module: using a simple 4 wire shielded cable it's possible to supply and interconnect up to 30 modules like this, through RS485 ModBus protocol already implemented in Domoticz (a plugin must be installed): RS485 is a strong communication system, easier to be connected than ethernet, with no RF pollution, and already includes 12/24V power supply in the bus cable.

Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.

Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.

Can be used to measure level of water or other liquid inside a tank, for example.

Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.

Alkaline battery for remote controls, 12V 20mAh. 27x7.6mm

Smart EVSE module to make DIY EV charging station (wallbox) that also works with Domoticz home automation system

DC/DC switching converter with 8-20V input, 5V 3A output with USB Type-C connector

Multifrequency universal door opener which permit to activate an electric lock or electric strike plate, using almost any remote control in the market, both fixed and rolling code, AM and FM, which transmit in the frequency 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315 or 418 MHz.

Can be installed in 5 minutes!

Waterproof NTC temperature sensor, 10k @25°C, 1%, B=3950

Universal multi-frequency receiver with 2 outputs, 60V 50mA load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz. Also, it can be programmed to work in 2 frequency simultaneously.

Standard antenna with stainless steel wall mount bracket.

2.1dB gain, 15MHz bandwidth, from 860 to 880 MHz

Very high quality, long life, made in Italy.

Meanwell HDR-15-12 compatible 12V 15W power supply, DIN rail 1 module (16.5mm width). 100-240Vin 50-60Hz, 10.8-13.8 Vout (adjustable) 1.25A max current.

Original SanDisk microSDHC memory, High Endurance, 64GB, U3 V30 Class10 40MB/s write speed, 100MB/s read speed.

Already programmed with Raspbian and Domoticz, suitable for Raspberry PI3, Raspberry PI4, Rock PI S.

Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.

Contacts are protected from overcurrent and overvoltage.

Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.

Professional 100m flex cable for RS485 (and Modbus) serial bus. 4 wires + shield: 2*0.22mm twisted (120 ohm impedance, for data) + 2*0.5mm (for supply) + shielding. External diameter 5.5mm.

The ideal cable to connect Creasol DomBus I/O expanders to Domoticz home automation controller.

Creasol DomBus23 is a module for home automation system with several different kind of inputs/outputs in a short size:  74x72x24mm.

It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus23 is designed to consume low power, be reliable, fully configurable and easy to use.

1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC

+/- 0.5K accuracy, 9-12bit resolution.

Suitable for Domoticz/RaspberryPI and ESP8266 controllers

3V lithium cell, button size, 20mm diameter, 3.2mm thickness. Suitable for remote controls and other electronic devices.

DIN RAIL module, 115x90x40mm, supporting both DomBus and Modbus RTU protocols.

It integrates 12x low voltage analog/digital inputs, 3x relays outputs, 3x 115Vac / 230Vac inputs. Optionally it is able to control and monitor the power supply fed to a burglar alarm external siren. Useful to make burglar alarm systems with home automation controllers like Domoticz, Home Assistant, OpenHAB, ...

DIN-rail modular 40A 230V 2P contactor with 230Vac coil with only 1.6W coil power.

USB cable, 1m long, with switch.
Type-A male USB connector on one side, Type-C male USB connector on the other side.

Suitable for Raspberry PI 4 , modern smartphones and other devices.

DIN rail module within 12 relays, 5A 250V, supporting DomBus and Modbus RTU protocols (to be selected), for industrial automation and home automation systems, like Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Very low power consumption, less than 750mW with all 12 relays ON.

Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.

Electric vehicle charging cable, 8 kW,  32 Ampere, single-phases, with white Type-2 plug on one side, open on other side, so it's possible to connect to a home made wallbox using the Smart EVSE module DomBusEVSE