Showing 1-12 of 12 item(s)
Showing 1-12 of 12 item(s)
Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).
€41.48
-30%
€29.04
Modbus energy meter:
230V 50Hz 100A max
Modbus protocol (RS485)
€18.18
Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.
€132.98
-30%
€93.09
Plug & Play home automation KIT, completed with preinstalled software and power supply, with 3 domotic modules: DomBus31 (8 relay outputs), DomBus12 (9 inputs/outputs), DomBusTH (temperature+humidity sensor, red/green/white LEDs, 6 inputs/outputs) and DomRelay2 (2 relays module)
€160.00
Waterproof NTC temperature sensor, 10k @25°C, 1%, B=3950
€2.68
-30%
€1.88
Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.
€154.00
DomBus34 is a DIN-RAIL module, 54mm wide, designed to interface up to 4 power/energy meters, type DDS 238-2 ZN/S (Modbus), to measure power and energy (both imported and exported), voltage frequency and power factor.
It implements 2 relay outputs 250V 5A SPST with overvoltage protection, 1 AC input 110-240Vac, and 2 low-voltage inputs that can be connected to pushbuttons and switches, double pushbuttons and counters.
€70.76
-30%
€49.53
Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.
€48.80
-30%
€34.16
DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).
€32.94
-30%
€23.06
Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.
Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.
Can be used to measure level of water or other liquid inside a tank, for example.
Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.
€8.54
NOT AVAILABLE
Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz
€207.40
-30%
€145.18
1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC
+/- 0.5K accuracy, 9-12bit resolution.
Suitable for Domoticz/RaspberryPI and ESP8266 controllers
€2.93