Introduction

This multi-frequency universal receiver has 2 relay outputs, with 250V and 5A capability, and can be supplied from 7Vdc to 36Vdc, and from 7Vac to 27Vac.

Frequency can be set easily using the Prog button, as like as the relay output that can be configured, indipendently for each channel, to hold-to-run, bistable, bistable ON/OFF (1 button to turn output ON, and another button to turn it OFF), and timer from 0.5s to 60 minutes.

It supports up to 1000 different remote controls in the same receiver, both fixed and rolling code, AM and FM: the maximum number depends by the code length, for example it supports up to 600 KeeLoq codes.

Programmed remote controls and configuration can be saved in a standard eeprom memory (check that it works at 3V!), so it's possible to save or restore configuration directly from the receiver.

Also, it can receive in one or two different frequencies, even with different modulation.

Creasol UniRec2 can be used to:

• control an electronic board with two pushbutton inputs, or two electronic boards with one pushbutton input/each.
• activate a motor up/down, for example a roller shutter motor (for this function, set for both outputs the  parameter 7 to 4, to prevent motor coils to be supplied simultaneously).
• activate an async motor or pump
• activate one or more lights

Using your existing remote control, it's possible for example to:

1. open your garage door or gate, using the existing electronic board and receiver, but adding support to new remote controls;
2. activate / disable the garden lights by using one channel of Creasol UniRec2 receiver in timer mode;
3. activate / disable the sink pump using the second channel of Creasol UniRec2 receiver in timer mode;
4. open your entrance door or pedestrian gate, but in this case it's recommended to use the more compact and easy Creasol UniLock device.

The product is made in Europe, provided in a nice transparent resealable recyclable clamshell, with instructions printed in several languages.

We also offer any customization to companies that like to purchase at least 100pcs: please send inquiry by email to sales@creasol.it , specifying company details and special requests.

Features

• Can be supplied  from 7 to 36Vdc and from 7 to 27Vac.

• Frequency selected by the user: 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315^*, 288^*, 300^*, 303^*, 306^*, 310^*, 318^*, 330^*, 390^*, 403.55^*, 418^* MHz. Frequencies marked with ^* cannot be used inside EU. The frequency of the remote control must be stable, so it does not work with remote controls without crystal or saw resonator (some bad remote controls operating around 300 MHz)!

• OOK (AM) and FSK (FM) modulation is supported: FM with 2 different deviation value, 12 and 24 KHz; AM with standard and narrow bandwidth (higher sensitivity)

• Twin frequency receiver: the user can select one or two frequencies/modulations as preferred, so it can receive, for example, at one single frequency or both 433 MHz OOK and 868 MHz FSK, or both 868MHz OOK and 315MHz OOK, or any combination of frequencies and modulations.

• Works with a wide range of remote controls which transmit fixed or rolling code. See the compatibility table.

• Manages different types of remote controls in the same time.

• It's possible to learn one or more "master remote controls" that can be use just to enable learning for 10s without the need to access the receiver to press the Prog button.

• High voltage and current contact rating: relay outputs support up to 250Vac and 5A (1kVA), using resistive load. Relay contacts are protected from overvoltage.

• Wide output configurations: hold-to-run, bistable, bistable ON/OFF (1 remote control button to activate output, another button to disable output), timer from 500ms to 60 minutes.

• Optional memory: it's possible to install a cheap optional non-volatile memory to get the programmed remote controls and configuration saved into the external memory: by default the receiver will use the configuration in the external memory, and it's possible to copy external memory to internal and viceversa using parameter 10 (please check the configuration table).

Documentation

• Creasol UniRec2 instructions in PDF format

• Creasol UniRec2 video
• Application notes that show our products in brief and some examples/schematics, in PDF format
• Application notes for UniRec2 receiver
• Pictures, width 400px: open , closed, packed in blister