Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).

Creasol DomBus12 is a compact module, 40x30x11mm, with 9 configurable inputs/outputs.
It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus12 is designed to consume low power, be reliable, fully configurable and easy to use.

Creasol DomBus31 is a din-rail relay module, 115x90x40mm, with 8 relays outputs. 6 relays are SPST (Normally Open outputs) with 250V 5A max capability, and 2 relays are SPDT (Normally Open and Normally Closed outputs) with 10A capability. It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus31 provides excellent performance in terms of power optimization: with all 8 relays active (the worst case), the power consumption is only 500mW! As a comparison, KMTronic 8 relays module consumes 12W, Denkovi 8 relays board consumes about 3W, Sonoff Dual R2 consumes 2W with only 2 relays enabled.

Suitable to be used as Domoticz relays module: using a simple 4 wire shielded cable it's possible to supply and interconnect up to 30 modules like this, through RS485 ModBus protocol already implemented in Domoticz (a plugin must be installed): RS485 is a strong communication system, easier to be connected than ethernet, with no RF pollution, and already includes 12/24V power supply in the bus cable.

Creasol DomBus23 is a module for home automation system with several different kind of inputs/outputs in a short size:  74x72x24mm.

It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).

As other DomBus devices, DomBus23 is designed to consume low power, be reliable, fully configurable and easy to use.

Smart EVSE module to make DIY EV charging station (wallbox) that also works with Domoticz home automation system

DIN rail module within 12 relays, 5A 250V, supporting DomBus and Modbus RTU protocols (to be selected), for industrial automation and home automation systems, like Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Very low power consumption, less than 750mW with all 12 relays ON.

DIN RAIL module, 115x90x40mm, supporting both DomBus and Modbus RTU protocols.

It integrates 12x low voltage analog/digital inputs, 3x relays outputs, 3x 115Vac / 230Vac inputs. Optionally it is able to control and monitor the power supply fed to a burglar alarm external siren. Useful to make burglar alarm systems with home automation controllers like Domoticz, Home Assistant, OpenHAB, ...

DIN-rail module designed to domotize 3 existing lights using 230V pushbutton and step-by-step relay.
The relay is used to toggle the external step-by-step relay (sending a pulse to its 230V coil) and AC input is used to monitor the light status (ON/OFF).
The 5 analog/digital I/O can be connected to low-voltage pushbuttons, counters, temperature distance and alarm sensors.

Very compact and low power consumption module with 3 relays 15A, 1 AC input, 4 analog/digital inputs.

DIN-rail high reliability and low power home automation module with relays output, low voltage inputs and one 100-250Vac input.Works with home automation systems like Domoticz, Home Assistant, Node-RED, OpenHAB and more...

Can be used to manage alarm sensors, pushbuttons, lights and other loads, and monitor 230V presence (detecting power outage).

2 axis sun tracker controller in low-profile din-rail enclosure, working in stand-alone and also working with home automation systems like Domoticz, HomeAssistant, NodeRED, Modbus, ...

Universal multi-frequency receiver with 2 relay outputs and 250V 5A load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz.

Remote control transmitter and duplicator, 433.920 MHz.
Easily copy almost all fixed-code remote controls in the market.

DomBus34 is a DIN-RAIL module, 54mm wide, designed to interface up to 4 power/energy meters, type DDS 238-2 ZN/S (Modbus), to measure power and energy (both imported and exported), voltage frequency and power factor.
It implements 2 relay outputs 250V 5A SPST with overvoltage protection, 1 AC input 110-240Vac, and 2 low-voltage inputs that can be connected to pushbuttons and switches, double pushbuttons and counters.

DIN-rail module with 3 relays, 3 AC inputs and 5 configurable I/O.
Suitable for Domoticz home automation system (DomBus firmware version) or other automations (Home Assistant, Node-RED, OpenHAB, ... using Modbus version)

Connect more I/O and sensors to Domoticz using Creasol DomESP2.

Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).

This is a package with 3x relay modules DomRelay2 (3pcs)

Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.

Contacts are protected from overcurrent and overvoltage.

Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.

Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.

Contacts are protected from overcurrent and overvoltage.

Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.

Long range 433.92 MHz remote control duplicator, in light-weight soft-touch shell

Connect more I/O and sensors to Domoticz using Creasol DomESP1.

Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

Also the DomESP2 board is available, using plugin terminal blocks!

1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC

+/- 0.5K accuracy, 9-12bit resolution.

Suitable for Domoticz/RaspberryPI and ESP8266 controllers

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

With 3 digits display showing the input and output voltage.

Size: 61x34x12mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 48x23x14mm

High performance filtered antenna with stainless steel wall mount bracket, with 3m coax cable RG58 and male-SMA connector.

3m coax cable, RG58, and SMA male connector. Suitable for RFXCOM and other transmitter, receivers, transceivers operating at 433MHz, 434MHz or 435MHz.

2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz

Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.

Very high quality, long life, made in Italy.

Universal multi-frequency receiver with 2 outputs, 60V 50mA load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz. Also, it can be programmed to work in 2 frequency simultaneously.

Multifrequency remote control duplicator, in plastic case with soft touch feeling, available in 6 colors.

Automatically learn frequency and code of original remote controls, transmitting at 433.92MHz, 868.3MHz and from 220 to 418 MHz (not for EU version, where these frequencies are disabled).

Very easy to program, each button is indepent and can work in a different frequency.

Standard antenna with stainless steel wall mount bracket.

2.1dB gain, 15MHz bandwidth, from 860 to 880 MHz

Very high quality, long life, made in Italy.

As remote control manufacturers, we have the knowledge to repair faulty remote controls.

We provide the remote control repairs service for a fixed price.

Multifrequency micro receiver, 1 channel, operating at 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315, 403.55, 418 MHz. Can be used to replace a non-working receiver, or to control an existing electronic board by almost any remote control in the market, both fixed and rolling code, AM and FM.
The receiving frequency and modulation can be programmed by the user: also, it's possible to program 2 different frequencies, even with different modulation, to manage remote controls transmitting in 2 different frequencies/modulations: for example the receiver can be used by a set of 433.92MHz OOK and 868.8MHz FSK remote controls.

Multifrequency universal door opener which permit to activate an electric lock or electric strike plate, using almost any remote control in the market, both fixed and rolling code, AM and FM, which transmit in the frequency 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315 or 418 MHz.

Can be installed in 5 minutes!

Multifrequency long range transmitter and remote control duplicator, which can be connected to 1-4 external switches. Transmission frequency and transmission power can be selected by the user, independetly for each channel, using the Prog button. When each switch changes its state, SenderB att starts transmitting the programmed/recorded code in the selected frequency.

Suitable for domotic systems, to transmits up to 4 or 6 different codes depending by the 4 inputs configuration.

Multifrequency long-range remote control duplicator which should be connected, by a pushbutton, to an external power supply. Can be used inside a car, to open gate/door, by flashing highbeam lights or brake pedal.
Copy up to 4 fixed-code remote controls, even in different frequencies.

Universal remote control duplicator, which is able to copy up to 4 different remote controls which transmit at 433.92 MHz.
Four buttons, very easy programming, strong, nice look, very long range!

Remote control duplicator that is able to copy up to 4 remote controls which transmit in these frequencies: 433.92, 868.3, 315, 403.55, 418, 286-360, 384-400 MHz.
Four buttons, automatic frequency detection, very easy programming, nice look!
Can operate in different frequencies (one for each button).