Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: fast and cheap - Express Courier: fast and safe
Before returning products, please contact us
Domotic modules for home automation systems, designed for Domoticz and Home Assistant
Universal receivers, multi-frequency, with 1 or more channels, that can be used with almost any remote control in the market that transmit at 433.92, 868.3 and other frequencies between 288 and 418 MHz, fixed and rolling code.
A special receiver, UniLock, can be used to activate an electric lock or electric strike plate: very easy to be connected, it's suitable for the main door and pedestrian gate. In this way you can open your main door or pedestrian gate using your existing remote control.
Hand-held remote control duplicators, single frequency or multifrequency, with nice design and good performances.
Also, stationary remote control duplicators / transmitters, which work in more than 1 frequency (for example button 1 at 433.92MHz, and button 2 at 868.3 MHz ); supplied externally ( from 7 to 35Vdc, or from 5 to 24Vac ) or internally (by a CR2032 long-life cell ).
Strong and long life antennas for receivers and other devices.
Antennas are supplied with 3m RG58 coax cable, stainless steel wall bracket and screws, removable whip and hole for water drain.
Optionally it's possible to supply antennas with SMA male or female connector.
Cells and batteries, mainly used on remote controls. Alkaline and lithium type.
Repair service for remote controls and car keys.
Ability to repair your own remote control or car key at a predetermined price.
Very rarely remote controls or car keys cannot be repaired: in this case you will be charged the only shipping cost to return back the device: you should pay nothing if the unrepairable device can be trashed.
Before sending us any remote control or car key, please send an email to store@creasol.it with any information about the device, defect and, if possible, a picture that shows the defect.
Active filters
KIT to make a home made smart wallbox, single phase, working with Home Assistant, NodeRED, Domoticz, ...
KIT to make a home made smart wallbox, threee phase, working with Home Assistant, NodeRED, Domoticz, ...
Connect one or more DomBus networks of modules with any industrial or home automation system using MQTT or MQTT-AD
DIN-rail high reliability and low power home automation module with relays output, low voltage inputs and one 100-250Vac input.Works with home automation systems like Domoticz, Home Assistant, Node-RED, OpenHAB and more...
Can be used to manage alarm sensors, pushbuttons, lights and other loads, and monitor 230V presence (detecting power outage).
DIN RAIL module, 115x90x40mm, supporting both DomBus and Modbus RTU protocols.
It integrates 12x low voltage analog/digital inputs, 3x relays outputs, 3x 115Vac / 230Vac inputs. Optionally it is able to control and monitor the power supply fed to a burglar alarm external siren. Useful to make burglar alarm systems with home automation controllers like Domoticz, Home Assistant, OpenHAB, ...
Plug & Play home automation KIT, completed with preinstalled software and power supply, with 3 domotic modules: DomBus31 (8 relay outputs), DomBus12 (9 inputs/outputs), DomBusTH (temperature+humidity sensor, red/green/white LEDs, 6 inputs/outputs) and DomRelay2 (2 relays module)
DIN rail module within 12 relays, 5A 250V, supporting DomBus and Modbus RTU protocols (to be selected), for industrial automation and home automation systems, like Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Very low power consumption, less than 750mW with all 12 relays ON.
Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.
Smart EVSE module to make DIY EV charging station (wallbox) that also works with Domoticz home automation system
Nice gift to start home automation systems, for students and people with some skills.
Plug & Play KIT using Rock PI S mini computer with metal case, already equipped with high quality 32GB memory card, Debian Linux, Domoticz, firewall, backup, a RS485 to USB adapter and a DomBusTH domotic module.
Creasol DomBus23 is a module for home automation system with several different kind of inputs/outputs in a short size: 74x72x24mm.
It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).
As other DomBus devices, DomBus23 is designed to consume low power, be reliable, fully configurable and easy to use.
Creasol DomBus31 is a din-rail relay module, 115x90x40mm, with 8 relays outputs. 6 relays are SPST (Normally Open outputs) with 250V 5A max capability, and 2 relays are SPDT (Normally Open and Normally Closed outputs) with 10A capability. It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).
As other DomBus devices, DomBus31 provides excellent performance in terms of power optimization: with all 8 relays active (the worst case), the power consumption is only 500mW! As a comparison, KMTronic 8 relays module consumes 12W, Denkovi 8 relays board consumes about 3W, Sonoff Dual R2 consumes 2W with only 2 relays enabled.
Suitable to be used as Domoticz relays module: using a simple 4 wire shielded cable it's possible to supply and interconnect up to 30 modules like this, through RS485 ModBus protocol already implemented in Domoticz (a plugin must be installed): RS485 is a strong communication system, easier to be connected than ethernet, with no RF pollution, and already includes 12/24V power supply in the bus cable.
Creasol DomBus12 is a compact module, 40x30x11mm, with 9 configurable inputs/outputs.
It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).
As other DomBus devices, DomBus12 is designed to consume low power, be reliable, fully configurable and easy to use.
Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).
Connect more I/O and sensors to Domoticz using Creasol DomESP1.
Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.
DIN-rail module with 3 relays, 3 AC inputs and 5 configurable I/O.
Suitable for Domoticz home automation system (DomBus firmware version) or other automations (Home Assistant, Node-RED, OpenHAB, ... using Modbus version)
DIN-rail module designed to domotize 3 existing lights using 230V pushbutton and step-by-step relay.
The relay is used to toggle the external step-by-step relay (sending a pulse to its 230V coil) and AC input is used to monitor the light status (ON/OFF).
The 5 analog/digital I/O can be connected to low-voltage pushbuttons, counters, temperature distance and alarm sensors.
Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.
DDS238-1 ZN/S Power Energy meter, bidirectional, with ModBus and 1 S0 (pulsed) output, 45A, single phase
Compact module, 43x24x25mm, within 2 relays with 12Vdc 200mW coil, 250V 5A SPST contact.
Contacts are protected from overcurrent and overvoltage.
Suitable to be connected to home automation systems like Creasol DomBus modules: indeed, using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.
Very compact and low power consumption module with 3 relays 15A, 1 AC input, 4 analog/digital inputs.
Single and dual axis sun tracker controller, working in stand-alone and also working with home automation systems like Domoticz, HomeAssistant, NodeRED, Modbus, ...
Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.
USB to RS485 adapter / converter with additional GND and +5V output.
Minimal KIT to start home automation system that measure power/energy consumption/production, display charts, control connected devices like air conditioning systems.
DC/DC switching converter with 8-20V input, 5V 3A output with USB Type-C connector
Connect more I/O and sensors to Domoticz using Creasol DomESP2.
Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.
This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).
Italiano
English
Deutsch
Français
Español
Português
Dutch
Danish
Norwegian
Swedish
Finnish
Czech
Hungarian
Latvian
Lithuanian
Polish
Romanian
Slovak
WiFicontroller ESP8266 original WeMos D1 Mini, 4MB flash.
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz or other controllers, by HTTP and MQTT.
Uses the chip ESP8266-12E with USB interface CH340G.
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...
Completed with pin header, male and female, provided apart (to be soldered, if needed)
USB to RS485 converter/adapter/interface.
Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.
Size: 61x18x14mm
