Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: fast and cheap - Express Courier: fast and safe
Before returning products, please contact us
Domotic modules for home automation systems, designed for Domoticz and Home Assistant
Universal receivers, multi-frequency, with 1 or more channels, that can be used with almost any remote control in the market that transmit at 433.92, 868.3 and other frequencies between 288 and 418 MHz, fixed and rolling code.
A special receiver, UniLock, can be used to activate an electric lock or electric strike plate: very easy to be connected, it's suitable for the main door and pedestrian gate. In this way you can open your main door or pedestrian gate using your existing remote control.
Hand-held remote control duplicators, single frequency or multifrequency, with nice design and good performances.
Also, stationary remote control duplicators / transmitters, which work in more than 1 frequency (for example button 1 at 433.92MHz, and button 2 at 868.3 MHz ); supplied externally ( from 7 to 35Vdc, or from 5 to 24Vac ) or internally (by a CR2032 long-life cell ).
Strong and long life antennas for receivers and other devices.
Antennas are supplied with 3m RG58 coax cable, stainless steel wall bracket and screws, removable whip and hole for water drain.
Optionally it's possible to supply antennas with SMA male or female connector.
Cells and batteries, mainly used on remote controls. Alkaline and lithium type.
Repair service for remote controls and car keys.
Ability to repair your own remote control or car key at a predetermined price.
Very rarely remote controls or car keys cannot be repaired: in this case you will be charged the only shipping cost to return back the device: you should pay nothing if the unrepairable device can be trashed.
Before sending us any remote control or car key, please send an email to store@creasol.it with any information about the device, defect and, if possible, a picture that shows the defect.
Coaxial cable for alarm system, 4x0,22mm², 100m
Cavo coassiale per antifurto, 4x0.22mmq, 4 fili da 0,22mmq, matassa 100m.
Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz
1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC
+/- 0.5K accuracy, 9-12bit resolution.
Suitable for Domoticz/RaspberryPI and ESP8266 controllers
USB to RS485 converter/adapter/interface.
Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.
Size: 61x18x14mm
Italiano
English
Deutsch
Français
Español
Português
Dutch
Danish
Norwegian
Swedish
Finnish
Czech
Hungarian
Latvian
Lithuanian
Polish
Romanian
Slovak
WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller.
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz.
Uses the chip ESP8266-12E with USB interface CH340G.
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...
Compact switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 0.85 to 12Vdc.
Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
Size: 18x10x4mm
Switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 3 to 35Vdc.
Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
With 3 digits display showing the input and output voltage.
Size: 61x34x12mm
Switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 3 to 35Vdc.
Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
Size: 48x23x14mm
Standard antenna with stainless steel wall mount bracket.
2.1dB gain, 15MHz bandwidth, from 860 to 880 MHz
Very high quality, long life, made in Italy.
High performance filtered antenna with stainless steel wall mount bracket.
2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz
Very high quality, long life, made in Italy.
Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.
Optional memory for universal receivers like UniRec2.
It can be installed in the receiver to supports a greater number of different remote controls.
Alkaline battery for remote controls, 12V 20mAh. 27x7.6mm
