Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: fast and cheap - Express Courier: fast and safe
Before returning products, please contact us
KITs with some home automation controller, modules and devices, to easily start a domotic system using our DomBus modules.
DomBus modules are designed for reliability and very low power consumption. They are available with two firmwares:
Modules and devices that should be applicable to electric cars, vans, trucks, bikes, ...
EV chargers, Type-2 cables, EV charging cable, EVSE modules, contactors, Type-B RCD RCCB, home automation systems integrating electric car charging, ...
If you know about electrical systems and home automation system, you can build a wallbox by yourself using:
More information to build a wallbox at https://www.creasol.it/EVSE
Home automation system / IoT controllers:
Single board computers like Raspberry PI and Rock PI S, equipped with Linux + Domoticz, ESP8266
DomBus modules (optimized low-power modules that works with Domoticz and other home automation systems)
ESP8266/ESP32 modules
Input and output modules for home automation systems , domotica and IoT. Relay board, SSR, pushbutton inputs, temperature sensors, dimmer, ...
Power supply modules, AC/DC, DC/DC, switching mode power supply, linear regulator, battery charger/controller.
Contactors, relays, and circuit breaker, including Type-B residual current detectors for electric car chargers
Wireless devices for domotics: 433MHz, 868MHz, Sub-1GHz, LTE, WiFi, Bluetooth, Zigbee, ZWave, 2.4GHz, 5GHz, ....
Domotic sensors, for temperature, humidity, pressure, gas, pollution, ....
DomBus modules integrating a temperature sensor and relative humidity (works with Domoticz and other home automation systems), NTC 10k temperature sensors, DS18B20 1-wire sensors, ...
Active filters
DIN-rail modular 25A 400V 4P contactor with 230Vac coil with only 1.6W coil power.
DIN-rail modular 40A 230V 2P contactor with 230Vac coil with only 1.6W coil power.
DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).
USB to RS485 adapter / converter with additional GND and +5V output.
Minimal KIT to start home automation system that measure power/energy consumption/production, display charts, control connected devices like air conditioning systems.
Modbus energy meter:
230V 50Hz 100A max
Modbus protocol (RS485)
Starter kit for your home automation system!
Content:
It's possible to replace the Domoticz software with Home Assistant Core or other type of software of your choice, using Linux Raspbian OS.
13.8V 8A power supply with 12V lead acid battery charger (UPS function)
Connect more I/O and sensors to Domoticz using Creasol DomESP2.
Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.
This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).
Italiano
English
Deutsch
Français
Español
Português
Dutch
Danish
Norwegian
Swedish
Finnish
Czech
Hungarian
Latvian
Lithuanian
Polish
Romanian
Slovak
WiFicontroller ESP8266 original WeMos D1 Mini, 4MB flash.
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz or other controllers, by HTTP and MQTT.
Uses the chip ESP8266-12E with USB interface CH340G.
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...
Completed with pin header, male and female, provided apart (to be soldered, if needed)
Case for Raspberry PI 4, official case.
Starter kit for your home automation system!
Content:
USB cable, 1m long, with switch.
Type-A male USB connector on one side, Type-C male USB connector on the other side.
Suitable for Raspberry PI 4 , modern smartphones and other devices.
Compact power supply with EU plug, 5V 3000mA, optimal for Raspberry PI 4 and for fast battery charging.
Output voltage: 5V
Output current: 3A.
EU plug.
No USB cable.
AVAILABLE ONLY AS domKit1 AND domKit2!
Raspberry PI 4 Single Board Computer, Model B, 2GB RAM.
Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz
USB to RS485 converter/adapter/interface.
Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.
Size: 61x18x14mm
WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller.
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz.
Uses the chip ESP8266-12E with USB interface CH340G.
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...
Compact switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 0.85 to 12Vdc.
Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
Size: 18x10x4mm
Switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 3 to 35Vdc.
Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
With 3 digits display showing the input and output voltage.
Size: 61x34x12mm
Switching mode power supply, voltage regulator.
Output current: 2A.
Vin: from 3 to 35Vdc.
Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.
Drop-out voltage: 1.5V.
Size: 48x23x14mm
