Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: fast and cheap - Express Courier: fast and safe
Before returning products, please contact us
Domotic modules for home automation systems, designed for Domoticz and Home Assistant
KITs with some home automation controller, modules and devices, to easily start a domotic system using our DomBus modules.
DomBus modules are designed for reliability and very low power consumption. They are available with two firmwares:
Modules and devices that should be applicable to electric cars, vans, trucks, bikes, ...
EV chargers, Type-2 cables, EV charging cable, EVSE modules, contactors, Type-B RCD RCCB, home automation systems integrating electric car charging, ...
If you know about electrical systems and home automation system, you can build a wallbox by yourself using:
More information to build a wallbox at https://www.creasol.it/EVSE
Home automation system / IoT controllers:
Single board computers like Raspberry PI and Rock PI S, equipped with Linux + Domoticz, ESP8266
DomBus modules (optimized low-power modules that works with Domoticz and other home automation systems)
ESP8266/ESP32 modules
Input and output modules for home automation systems , domotica and IoT. Relay board, SSR, pushbutton inputs, temperature sensors, dimmer, ...
Power supply modules, AC/DC, DC/DC, switching mode power supply, linear regulator, battery charger/controller.
Contactors, relays, and circuit breaker, including Type-B residual current detectors for electric car chargers
Wireless devices for domotics: 433MHz, 868MHz, Sub-1GHz, LTE, WiFi, Bluetooth, Zigbee, ZWave, 2.4GHz, 5GHz, ....
Domotic sensors, for temperature, humidity, pressure, gas, pollution, ....
DomBus modules integrating a temperature sensor and relative humidity (works with Domoticz and other home automation systems), NTC 10k temperature sensors, DS18B20 1-wire sensors, ...
KIT to make a home made smart wallbox, single phase, working with Home Assistant, NodeRED, Domoticz, ...
KIT to make a home made smart wallbox, threee phase, working with Home Assistant, NodeRED, Domoticz, ...
Plug & Play home automation KIT, completed with preinstalled software and power supply, with 3 domotic modules: DomBus31 (8 relay outputs), DomBus12 (9 inputs/outputs), DomBusTH (temperature+humidity sensor, red/green/white LEDs, 6 inputs/outputs) and DomRelay2 (2 relays module)
Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.
Nice gift to start home automation systems, for students and people with some skills.
Plug & Play KIT using Rock PI S mini computer with metal case, already equipped with high quality 32GB memory card, Debian Linux, Domoticz, firewall, backup, a RS485 to USB adapter and a DomBusTH domotic module.
Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).
Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.
DDS238-1 ZN/S Power Energy meter, bidirectional, with ModBus and 1 S0 (pulsed) output, 45A, single phase
Sun light sensor for single and dual axis controllers like DomBusTracker and DomBusTracker2
Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.
DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).
Minimal KIT to start home automation system that measure power/energy consumption/production, display charts, control connected devices like air conditioning systems.
Modbus energy meter:
230V 50Hz 100A max
Modbus protocol (RS485)
Waterproof NTC temperature sensor, 10k @25°C, 1%, B=3950
Starter kit for your home automation system!
Content:
It's possible to replace the Domoticz software with Home Assistant Core or other type of software of your choice, using Linux Raspbian OS.
Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.
Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.
Can be used to measure level of water or other liquid inside a tank, for example.
Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.
Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz
1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC
+/- 0.5K accuracy, 9-12bit resolution.
Suitable for Domoticz/RaspberryPI and ESP8266 controllers
Italiano
English
Deutsch
Français
Español
Português
Dutch
Danish
Norwegian
Swedish
Finnish
Czech
Hungarian
Latvian
Lithuanian
Polish
Romanian
Slovak
