DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).

Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.

DIN-rail modular 25A 400V 4P contactor with 230Vac coil with only 1.6W coil power.

Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.

Professional 100m flex cable for RS485 (and Modbus) serial bus. 4 wires + shield: 2*0.22mm twisted (120 ohm impedance, for data) + 2*0.5mm (for supply) + shielding. External diameter 5.5mm.

The ideal cable to connect Creasol DomBus I/O expanders to Domoticz home automation controller.

Meanwell HDR-15-12 compatible 12V 15W power supply, DIN rail 1 module (16.5mm width). 100-240Vin 50-60Hz, 10.8-13.8 Vout (adjustable) 1.25A max current.

USB to RS485 adapter / converter with additional GND and +5V output.

DIN-rail modular 25A 230V 2P contactor with 230Vac coil with only 1.2W coil power.

Can be used with DomBus23 and DomBus31 domotic modules.
It can also be controlled by DomBusTH and DomBus12 through the DomRelay2 module.

DIN-rail modular 40A 230V 2P contactor with 230Vac coil with only 1.6W coil power.

Optional memory for universal receivers like UniRec2.

It can be installed in the receiver to supports a greater number of different remote controls.

Home automation module that can be used as a stand-alone single or dual axis solar tracker, working autonomously.

Can also be controlled by a home automation system, like Domoticz (using DomBus firmware + Domoticz plugin), Home Assistant, Node-RED, OpenHAB, ioBroker and other systems supporting MQTT protocol using DomBus firmware + DomBusGateway (a python software performing DomBus2MQTT bridge), or custom applications and other sustems supporting the Modbus protocol (using DomBusTracker2 version with Modbus firmware).
Sun light sensor NOT included, but we have a waterproof version with 5m long cable that can be purchased from our store.

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 48x23x14mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

With 3 digits display showing the input and output voltage.

Size: 61x34x12mm

Waterproof NTC temperature sensor, 10k @25°C, 1%, B=3950

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

NOT AVAILABLE

Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz