Starter kit for your home automation system!

Content:

• 1x Raspberry PI4 + original plastic case
  
  
• 1x 32gb high-endurance microSD already programmed with Raspbian + Domoticz + Firewall + Backup
  
  
• 1x RS485-to-USB adapter
  
  
• 1x Creasol DomBus31 (8 relay outputs)
  
  
• 1x Creasol DomBusTH (temperature+relative humidity sensor, white+red+green leds, 4 inputs, 2 outputs, 1 analog input)
  
  
• 1x Power supply unit, 13.8V 8A output, with 12V battery charger and UPS function
  
  
• 1x DC/DC converter, 12-24V input, 5V 3A (15W) output with USB type-C connector
  
  

It's possible to replace the Domoticz software with Home Assistant Core or other type of software of your choice, using Linux Raspbian OS.

13.8V 8A power supply with 12V lead acid battery charger (UPS function)

DIN-rail modular 25A 230V 2P contactor with 230Vac coil with only 1.2W coil power.

Can be used with DomBus23 and DomBus31 domotic modules.
It can also be controlled by DomBusTH and DomBus12 through the DomRelay2 module.

Connect more I/O and sensors to Domoticz using Creasol DomESP2.

Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).

WiFicontroller ESP8266 original WeMos D1 Mini, 4MB flash. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz or other controllers, by HTTP and MQTT. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

Completed with pin header, male and female, provided apart (to be soldered, if needed)

Case for Raspberry PI 4, official case.

Starter kit for your home automation system!

Content:

• 1x Raspberry PI4 genuine (without case)
• 1x 32gb high-endurance microSD already programmed with Raspbian + Domoticz + Firewall + Backup
• 1x RS485-to-USB adapter
• 1x Creasol DomBus1 (2 relay outputs, 6 inputs, 1 AC input)
• 1x Creasol DomBusTH (temperature+relative humidity sensor, white+red+green leds, 4 inputs, 2 outputs, 1 analog input)

USB cable, 1m long, with switch.
Type-A male USB connector on one side, Type-C male USB connector on the other side.

Suitable for Raspberry PI 4 , modern smartphones and other devices.

Compact power supply with EU plug, 5V 3000mA, optimal for Raspberry PI 4 and for fast battery charging.

Output voltage: 5V

Output current: 3A.

EU plug.

No USB cable.

Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.

Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.

Can be used to measure level of water or other liquid inside a tank, for example.

Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.

AVAILABLE ONLY AS domKit1 AND domKit2!

Raspberry PI 4 Single Board Computer, Model B, 2GB RAM.

Professional 100m flex cable for RS485 (and Modbus) serial bus. 4 wires + shield: 2*0.22mm twisted (120 ohm impedance, for data) + 2*0.5mm (for supply) + shielding. External diameter 5.5mm.

The ideal cable to connect Creasol DomBus I/O expanders to Domoticz home automation controller.

Coaxial cable for alarm system, 4x0,22mm², 100m

Cavo coassiale per antifurto, 4x0.22mmq, 4 fili da 0,22mmq, matassa 100m.

NOT AVAILABLE

Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz

1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC

+/- 0.5K accuracy, 9-12bit resolution.

Suitable for Domoticz/RaspberryPI and ESP8266 controllers

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

Compact switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 0.85 to 12Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 18x10x4mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc,regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

With 3 digits display showing the input and output voltage.

Size: 61x34x12mm

Switching mode power supply, voltage regulator.

Output current: 2A.

Vin: from 3 to 35Vdc.

Vout: from 1.5 to 33Vdc, regulated by trimming the potentiometer knob.

Drop-out voltage: 1.5V.

Size: 48x23x14mm