• -32%
Creaso UniRec12 - 2 channels compact multifrequency receiver
  • Creaso UniRec12 - 2 channels compact multifrequency receiver

Creaso UniRec12 - 2 channels compact multifrequency receiver

Universal multi-frequency receiver with 2 outputs, 60V 50mA load capability. Works with almost every remote control in the market, fixed and rolling code, AM and FM, transmitting at 433.42, 433.92, 434.15, 434.42, 868.3 868.5, 868.8, 288, 300, 303, 306, 310, 315, 318, 390, 403.55, 418 MHz. Also, it can be programmed to work in 2 frequency simultaneously.

€53.68
€36.50 Save 32%
Delivered in 1-2 working days

Volume discounts

Quantity Discount Price You Save
1 32% €36.50 €17.18
2 35% €34.89 €37.58
3 37% €33.82 €59.58
4 39% €32.74 €83.74
6 42% €31.13 €135.27
9 45% €29.52 €217.40
Quantity
Available

  • Full support on our products: we're the manufacturer and know very well our products! ;-) Full support on our products: we're the manufacturer and know very well our products! ;-)
  • Order are shipped in 1-2 working day Order are shipped in 1-2 working day
  • Made in Europe quality Made in Europe quality

Introduction

This multi-frequency universal receiver has 2 optocoupled outputs, with 60V and 50mA capability, and can be supplied from 5Vdc to 36Vdc, and from 7Vac to 27Vac.creUniRec12 400

Frequency can be setup easily using the Prog button, as like as the  output that can be configured, indipendently for each channel, to hold-to-run, bistable, bistable ON/OFF and timer from 0.5s to 60 minutes.

It supports up to 60 different remote controls in the same receiver, both fixed and rolling code, AM and FM: the maximum number depends by the code length.

Also, it can receive in one or two different frequencies, even with different modulation: for example it can be programmed to manage remote controls working in both AM 433.92 MHz and FM 868.8 MHz.

Creasol UniRec12 can be used to control an electronic board with two pushbutton inputs, or two electronic boards with one pushbutton input/each: for example it can be used to replace non-working receiver in a gate motor driver, or to add a different set of remote controls to an old automation working on low frequencies or using different codings.

Using your existing remote control, it's possible for example to:

  1. open your garage door or gate, using the existing electronic board and receiver;
  2. control other different automations by using one channel of Creasol UniRec12.

This device is not suitable to control power loads such as garden lights, motors, pump: in this case it's possible to use Creasol UniRec2.

The product is made in Europe, provided in a nice transparent resealable recyclable clamshell, with instructions printed in several languages.

We also offer any customization to companies that like to purchase at least 100pcs: please send inquiry by email to sales@creasol.it , specifying company details and special requests.

Features

  • Can be supplied  from 5 to 36Vdc and from 7 to 27Vac.

  • Frequency selected by the user: 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315*, 288*, 300*, 303*, 306*, 310*, 318*, 330*, 390*, 403.55*, 418* MHz. Frequencies marked with * cannot be used inside EU. The frequency of the remote control must be stable, so it does not work with remote controls without crystal or saw resonator (some bad remote controls operating around 300 MHz)!

  • OOK (AM) and FSK (FM) modulation is supported: FM with 2 different deviation value, 12.5 KHz and 25 KHz; AM with standard and narrow bandwidth (higher sensitivity)

  • Twin frequency receiver: the user can select one or two frequencies/modulations as preferred, so it can receive, for example, at one single frequency or both 433 MHz OOK and 868 MHz FSK, or both 868MHz OOK and 315MHz OOK, or any combination of frequencies.

  • Works with a wide range of remote controls which transmit fixed or rolling code. See the compatibility table.

  • Manages different types of remote controls in the same time.

  • It's possible to learn one or more "master remote controls" that can be use just to enable learning for 10s without the need to access the receiver to press the Prog button.

  • Low voltage and current contact rating: outputs support up to 60V and 50mA.

  • Wide output configurations: hold-to-run, bistable, bistable ON/OFF (1 remote control button to activate output, another button to disable output), timer from 250ms to 15 minutes.

Documentation

creUniRec12
494 Items

You might also like

Creasol Multi -...

Creasol Multi -...

Regular price €36.23 -32% Price €24.64
  • -32%
Creasol Sender - Stationary multifrequency remote control duplicator

Creasol Sender - Stationary...

Regular price €42.70 -32% Price €29.04
  • -32%
Creasol SenderBatt: 4 channels stationary multifrequency remote control duplicator/transmitter

Creasol SenderBatt: 4...

Regular price €48.80 -32% Price €33.18
  • -32%
Creasol UniLock: universal...

Creasol UniLock: universal...

Regular price €48.80 -32% Price €33.18
  • -32%
Creasol UniRec1 -...

Creasol UniRec1 -...

Regular price €48.80 -32% Price €33.18
  • -32%
creasol UniRec2 -...

creasol UniRec2 -...

Regular price €67.10 -32% Price €45.63
  • -32%
Creasol MultiST, coffee color

Creasol MultiST -...

Regular price €32.94 -32% Price €22.40
  • -32%
Creasol FourST - 433.92 MHz...

Creasol FourST - 433.92 MHz...

Regular price €23.18 -32% Price €15.76
  • -32%
chat Comments (0)
No customer reviews for the moment.