Domotics IoT

Electronic board with temperature, relative humidity and touch sensors, 4 inputs, 2 open-drain outputs, white led, red led, green led, analog input connected to Vbus, suitable to be connected to domotic controllers by RS485 serial bus (using a common 4 wires alarm cable: 2 for data, 2 for 12V power supply).

Modbus energy meter:
230V 50Hz 100A max
Modbus protocol (RS485)

Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.

Plug & Play home automation KIT, completed with preinstalled software and power supply, with 3 domotic modules: DomBus31 (8 relay outputs), DomBus12 (9 inputs/outputs), DomBusTH (temperature+humidity sensor, red/green/white LEDs, 6 inputs/outputs) and DomRelay2 (2 relays module)

Waterproof NTC temperature sensor, 10k @25°C, 1%, B=3950

Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.

DomBus34 is a DIN-RAIL module, 54mm wide, designed to interface up to 4 power/energy meters, type DDS 238-2 ZN/S (Modbus), to measure power and energy (both imported and exported), voltage frequency and power factor.
It implements 2 relay outputs 250V 5A SPST with overvoltage protection, 1 AC input 110-240Vac, and 2 low-voltage inputs that can be connected to pushbuttons and switches, double pushbuttons and counters.

Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.

DIN rail modular energy meter, with 1 pulsed output, 230V 65A max. 35mm wide (2 modules size).

Connect more I/O and sensors to Domoticz using Creasol DomESP2.

Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).

Ultrasonic distance sensor for arduino, domoticz, raspberry pi, Creasol DomBus1.

Waterproof sensor with 2.5m cable connected to the electronic board, that transmits a pulse which duration is proportional with the distance between sensor and reflecting surface.

Can be used to measure level of water or other liquid inside a tank, for example.

Can be easily interface with Raspberry + Domoticz using Creasol DomBus1 as interface.

Connect more I/O and sensors to Domoticz using Creasol DomESP1.

Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

Also the DomESP2 board is available, using plugin terminal blocks!

NOT AVAILABLE

Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz

1-wire digital temperature sensor, in TO-92 package, manufactured by Dallas/Maxim-IC

+/- 0.5K accuracy, 9-12bit resolution.

Suitable for Domoticz/RaspberryPI and ESP8266 controllers

WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

High performance filtered antenna with stainless steel wall mount bracket, with 3m coax cable RG58 and male-SMA connector.

3m coax cable, RG58, and SMA male connector. Suitable for RFXCOM and other transmitter, receivers, transceivers operating at 433MHz, 434MHz or 435MHz.

2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz

Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.

Very high quality, long life, made in Italy.