Domotics IoT

Smart EVSE module to make DIY EV charging station (wallbox) that also works with Domoticz home automation system

Electric vehicle charging cable, 11 kW,  16 Ampere, three-phases, with white Type-2 plug on one side, and white Type-2 socket on other side.

Bidirectional three-phase enegy and power meter with RS485 Modbus and 1 S0 pulsed output, configurable 400-6400 pulses/kWh, DIN rail, 4 modules wide.

Electric vehicle charging cable, 11 kW,  16 Ampere, three-phases, with white Type-2 plug on one side, open on other side, so it's possible to connect to a homemade wallbox build using the DomBusEVSE smart EVSE module.

Electric vehicle charging cable, 8 kW,  32 Ampere, single-phases, with white Type-2 plug on one side, open on other side, so it's possible to connect to a home made wallbox using the Smart EVSE module DomBusEVSE

Electric vehicle charging cable, 22 kW,  32 Ampere, three-phases, with white Type-2 plug on one side, and white Type-2 socket on other side.

DIN-rail modular 25A 400V 4P contactor with 230Vac coil with only 1.6W coil power.

Residual Current Circuit Breaker (RCCB) type-B, three phases, 400V 40A for electric vehicle charging stations and wallbox, with protection current 30mA AC and 6mA DC.
Compliant with IEC/EN61008-1 and IEC/EN62423.

Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.

Bidirectional enegy and power meter with RS485 Modbus and 1 S0 pulsed output, 2000 pulses/kWh, 65A max, DIN rail, 2 modules wide.

Residual Current Circuit Breaker (RCCB) type-B 240V 40A or 63A for electric vehicle charging stations and wallbox, single phase, with protection current 30mA AC and 6mA DC.
Compliant with IEC/EN61008-1 and IEC/EN62423.

Meanwell HDR-15-12 compatible 12V 15W power supply, DIN rail 1 module (16.5mm width). 100-240Vin 50-60Hz, 10.8-13.8 Vout (adjustable) 1.25A max current.

DC/DC switching converter with 8-20V input, 5V 3A output with USB Type-C connector

13.8V 8A power supply with 12V lead acid battery charger (UPS function)

DIN-rail modular 40A 230V 2P contactor with 230Vac coil with only 1.6W coil power.

Connect more I/O and sensors to Domoticz using Creasol DomESP2.

Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).

Connect more I/O and sensors to Domoticz using Creasol DomESP1.

Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.

Also the DomESP2 board is available, using plugin terminal blocks!

NOT AVAILABLE

Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz

USB to RS485 converter/adapter/interface.

Suitable for PC, Linux, RaspberryPI, to connect input/output modules or sensors by RS485 balanced bus.

Size: 61x18x14mm

WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller. 
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz. 
Uses the chip ESP8266-12E with USB interface CH340G. 
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...

High performance filtered antenna with stainless steel wall mount bracket, with 3m coax cable RG58 and male-SMA connector.

3m coax cable, RG58, and SMA male connector. Suitable for RFXCOM and other transmitter, receivers, transceivers operating at 433MHz, 434MHz or 435MHz.

2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz

Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.

Very high quality, long life, made in Italy.