1x Creasol DomBusTH (temperatur + relativ fuktighetssensor, vit + röd + grön lysdiod, 4 ingångar, 2 utgångar, 1 analog ingång)
Domoticz är en mycket enkel och kraftfull styrenhet för domotiska system, tillgänglig via webbläsare och Android / iOS-appen.
Raspberry är en minikomputerdator med ett kort, låg effekt (mindre än 10 watt), med fyrkärnig ARM-processor, lämplig för hemautomation.
DomBus1 är en enhet som kan placeras i väggkopplingsdosan för att styra lampor, pumpar, ventiler och läsa ingångar som dörr / fönster / blind magnetiska sensorer (för larm), PIR (för larm och närvaro), dörrklockknapp, .... Den är ansluten till Raspberry controller med en tunn kabel inom fyra ledningar (för larm eller bättre för RS485): 2 kablar för data (RS485 vid 115200bps, som tillåter att täcka upp till 1 km), 2 ledningar för 12 V ström leverans (bättre om batteriet backas upp)
DomBusTHär ett litet kort som kan placeras på ett tomt lock och är utformat för att mäta temperatur och relativ fuktighet. Den har också 3 lysdioder, vita + röda + gröna, som kan aktiveras för att meddela en status eller i händelse av strömavbrott (som en nödsituationlampa). Slutligen har den fyra konfigurerbara I / O (som kan anslutas till strömbrytare och tryckknappar, larmsensorer, summer, ...) och 2 öppna kollektorutgångar (lämpliga för att driva externa 12V-reläer).
RS485-lösningen tillåter:
undvika RF-förorening (orsakad av WiFi och andra trådlösa system)
använd en tunn kabel för att ansluta alla enheter via buss
försörja alla enheter med en 12V-strömförsörjning med batteri, så att hemautomatiseringssystemet fungerar även vid strömavbrott
Dessutom är detta system optimerat för låg energiförbrukning:
Hallon förbrukar mindre än 10 watt
DomBus1 förbrukar 0,050 W i standby och 0,3 W när alla 2 reläer är PÅ . Bara för att jämföra förbrukar Sonoff Dual R2 1,2 W i standby och mer än 2 W med bara 2 reläer PÅ.
DomBusTH förbrukar 0,03 W.
och är verkligen plug & play : anslut bara en ny DomBus-enhet till bussen, och du kan hitta i Domoticz Switches-panelen den enheten: ändra dess maskinvaruadress från switchpanelen för att tilldela en unik adress, och alla ingångar / utgångar / sensorer kommer att automatiskt tillgänglig i Domoticz automatiskt .
Vad kan du göra med Domoticz?
Kontrollera inomhus- och utomhusbelysning
Skapa ett pålitligt och komplett larmsystem som visar status på telefonen (Telegramapp) och skicka bilder / videor i händelse av någon händelse du vill.
Skicka en bild på smarttelefonen när någon ringer
Kontrollera porten och fotgängaren för att öppna dem på distans
Mät rumstemperatur och relativ fuktighet
Styr värmepumpen eller annan värmare / kylare: inget behov av termostat i varje rum, utan bara en osynlig termisk sensor i varje rum
Under vintern aktiverar elvärmare om solceller producerar mer energi än användningseffekt
Om värmepump och solceller är installerade optimerar du energiförbrukningen genom att reglera värmepumpen på den tillgängliga effekten från solceller.
Om ventilationssystemet är installerat, reglerar det att det kontrollerar luftfuktigheten i rummen och aktiverar avfuktaren (och kylspolen, om tillgänglig) under sommaren när solenergi är tillgänglig
Aktivera externa enheter som avfuktare, elektriska värmare, när det finns extra ström från solceller eller när rumsfuktighet / temperatur inte är bra.
Kontrollera nivån på regnvattentanken och kontrollera en ventil / pump för att vattna trädgården
Anslut till en meteostation och fånga data om regn, vind, temperatur, fuktighet, tryck, i fina diagram
Valfria tillgängliga produkter
Raspberry PI4 officiellt fodral, röd / vit, tillverkad i Storbritannien
5V 3A-adapter, för att leverera hallon
USB typ-C-kabel för att ansluta 5V-adapter till hallon (behövs för att ansluta5V 3A-adaptern till Raspberry
En av de tillgängliga 2A-omkopplingsregulatorerna för att minska 13,8 V (batterispänning) till 5 V, för att leverera hallon: passar när ett 12 V-batteri med batteriladdare / leverantör används för att leverera hemautomationssystemet
fler DomBus-enheter för att hantera fler ingångar, utgångar och sensorer
DomESP1 + ESP8266-modul, när du behöver styra enheter / sensorer via en WiFi-anslutning (standby-effekt: 0,5 W)
Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
very low power (around 10mW with relays OFF)
reliable (no disconnections)
bus connected (no radiofrequency interference, no battery to replace).
Modules are available in two version:
with DomBus proprietary protocol, working with Domoticz only
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Single-phase and three-phases, up to 36A (8kW or 22kW)
Needs external contactor, RCCB (protection) and EV cable
Optional power meter to measure charging power, energy, voltage and power factor
Optional power meter to measure the power usage from the grid (not needed if already exists)
Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)
DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
temperature and relative humidity sensor
red, green and white LEDs
4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.
DomBus12 - Compact domotic module with 9 I/Os
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
analog/digital inputs
pushbutton and UP/DOWN pushbutton
counters (water, gas, S0 energy, ...)
NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.
DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
3x high power latching relays SPST 15A: latching relay consumes nothing when ON
1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...
DomBus23 - Domotic module with many functions
Versatile module designed to control gate or garage door.
2x relays SPST 5A
1x 10A 30V mosfet (led stripe dimming)
2x 0-10V analog output: each one can be configured as open-drain output to control external relay
DIN rail low profile module, with 8 relays and very low power consumption:
6x relays SPST 5A
2x relays STDT 10A
Only 10mW power consumption with all relays OFF
Only 500mW power consumption with all 8 relays ON !!
DomBus32 - Domotic module with 3 relays
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
DomBus33 - Module to domotize a light system using step relays
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DomBus36 - Domotic module with 12 relays
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
12x relays SPST 5A
Relays are grouped in 3 blocks, with a single common per block, for easier wiring
Only 12mW power consumption with all relays OFF
Only 750mW power consumption with all 12 relays ON !!
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
3x 115/230Vac optoisolated inputs
2x relays SPST 5A
1x relay SPST 10A
DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs
DIN rail module designed for burglar alarm system.
4x relays SPDT (normally open + close contacts), 10A
2x relays SPST 10A
1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
Works in stand-alone mode (no need for external controller)
Can be connected to Domoticz for monitoring and controlling the motors position
DomRelay2 - 2x relays board
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
2x 5A 12V SPST relays (Normally Open contact)
Overvoltage protection (for inductive loads, like motors)
Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)
DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
9-24V input voltage, with high efficiency DC/DC regulator with 5V output
4x SPST relays 5V with overvoltage protection
1x SSR output (max 40V output)
2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
1x I²C interface for sensors, extended I/Os and more)
1x OneWire interface (DS18B20 or other 1wire sensors/devices)