Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: fast and cheap - Express Courier: fast and safe
Before returning products, please contact us
Domotic modules for home automation systems, designed for Domoticz and Home Assistant
KITs with some home automation controller, modules and devices, to easily start a domotic system using our DomBus modules.
DomBus modules are designed for reliability and very low power consumption. They are available with two firmwares:
Modules and devices that should be applicable to electric cars, vans, trucks, bikes, ...
EV chargers, Type-2 cables, EV charging cable, EVSE modules, contactors, Type-B RCD RCCB, home automation systems integrating electric car charging, ...
If you know about electrical systems and home automation system, you can build a wallbox by yourself using:
More information to build a wallbox at https://www.creasol.it/EVSE
Home automation system / IoT controllers:
Single board computers like Raspberry PI and Rock PI S, equipped with Linux + Domoticz, ESP8266
DomBus modules (optimized low-power modules that works with Domoticz and other home automation systems)
ESP8266/ESP32 modules
Input and output modules for home automation systems , domotica and IoT. Relay board, SSR, pushbutton inputs, temperature sensors, dimmer, ...
Power supply modules, AC/DC, DC/DC, switching mode power supply, linear regulator, battery charger/controller.
Contactors, relays, and circuit breaker, including Type-B residual current detectors for electric car chargers
Wireless devices for domotics: 433MHz, 868MHz, Sub-1GHz, LTE, WiFi, Bluetooth, Zigbee, ZWave, 2.4GHz, 5GHz, ....
Domotic sensors, for temperature, humidity, pressure, gas, pollution, ....
DomBus modules integrating a temperature sensor and relative humidity (works with Domoticz and other home automation systems), NTC 10k temperature sensors, DS18B20 1-wire sensors, ...
KIT to make a home made smart wallbox, single phase, working with Home Assistant, NodeRED, Domoticz, ...
KIT to make a home made smart wallbox, threee phase, working with Home Assistant, NodeRED, Domoticz, ...
Plug & Play home automation KIT, completed with preinstalled software and power supply, with 3 domotic modules: DomBus31 (8 relay outputs), DomBus12 (9 inputs/outputs), DomBusTH (temperature+humidity sensor, red/green/white LEDs, 6 inputs/outputs) and DomRelay2 (2 relays module)
Plug & Play home automation KIT with 1 energy meter and DomBus34 module that permits to manage up to 4 energy meters, control 2 loads (relays) and check 230V voltage presence.
Nice gift to start home automation systems, for students and people with some skills.
Plug & Play KIT using Rock PI S mini computer with metal case, already equipped with high quality 32GB memory card, Debian Linux, Domoticz, firewall, backup, a RS485 to USB adapter and a DomBusTH domotic module.
Connect more I/O and sensors to Domoticz using Creasol DomESP1.
Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.
High performance filtered antenna with stainless steel wall mount bracket, with 3m coax cable RG58 and male-SMA connector.
3m coax cable, RG58, and SMA male connector. Suitable for RFXCOM and other transmitter, receivers, transceivers operating at 433MHz, 434MHz or 435MHz.
2.1dB gain, 2MHz bandwidth, from 433 to 435 MHz
Thanks to the narrow bandwidth, it avoids noise/interference from systems transmitting in adjacent bands.
Very high quality, long life, made in Italy.
Minimal KIT to start home automation system that measure power/energy consumption/production, display charts, control connected devices like air conditioning systems.
Starter kit for your home automation system!
Content:
It's possible to replace the Domoticz software with Home Assistant Core or other type of software of your choice, using Linux Raspbian OS.
Connect more I/O and sensors to Domoticz using Creasol DomESP2.
Creasol DomESP2 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally 1100mils header pitch and WeMos D1 mini modules), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 MOSFET outputs.
This board is exactly the same as DomESP1, but with plugin terminal blocks (instead of screw terminal blocks).
Weather station that measure temperature, humidity, pressure, wind speed and direction and rain. Supply with a nice palm that shows all values.
Palm can be connected to Raspberry by a USB cable, so it's possible to get and accumulate all measures on Domoticz. Instructions to perform raspberry and domoticz configuration is available at https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-domoticz
Italiano
English
Deutsch
Français
Español
Português
Dutch
Danish
Norwegian
Swedish
Finnish
Czech
Hungarian
Latvian
Lithuanian
Polish
Romanian
Slovak
WiFicontroller ESP8266 NodeMcu V3, already programmed with ESPEasy firmware, accessible via web, ready to be used with Domoticz controller.
Can be used to integrate sensors and I/O that can be remotely controlled by Domoticz.
Uses the chip ESP8266-12E with USB interface CH340G.
Integrates GPIO, PWM, ADC, I2C, 1-Wire,...