• -32%

Creasol UniRec1 - Multifrequency 1 channel universal receiver

Multifrequency micro receiver, 1 channel, operating at 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315, 403.55, 418 MHz. Can be used to replace a non-working receiver, or to control an existing electronic board by almost any remote control in the market, both fixed and rolling code, AM and FM.

€48.80
€33.18 Save 32%
Delivered in 1-2 working days

Volume discounts

Quantity Discount Price You Save
1 32% €33.18 €15.62
2 35% €31.72 €34.16
3 37% €30.74 €54.17
4 39% €29.77 €76.13
6 42% €28.30 €122.98
9 45% €26.84 €197.64
Quantity
Available

  • Full support on our products: we're the manufacturer and know very well our products! ;-) Full support on our products: we're the manufacturer and know very well our products! ;-)
  • Order are shipped in 1-2 working day Order are shipped in 1-2 working day
  • Made in Europe quality Made in Europe quality

IntroductioncreRec12_200

This very small device, only 29x29x10mm, can be used with almost any radio remote control in the market which transmit in a frequency between 288 MHz and 868 MHz, AM and FM, fixed and rolling codes.

Also, it can receive in one or two different frequencies, even with different modulation.

It's very easy to be installed, using only two wires for the power supply and two opto-coupled wires which should be connected in parallel with the electronic board that should be remotely controlled.

The operating frequency, shown in the table, can be simply programmed using the Prog button, as like as the type of output which should be programmed as bistable, hold-to-run and as timer programmed from 250ms to 60 minutes.

In the same receiver it's possible to learn up to 60 different remote controls, even if different brand/model, both fixed and rolling code: the number of remote controls depends by the code complex, so, for example, it's possible to manage 40 KeeLoq rolling code remote controls.

When a known code is transmitted by the remote control, Creasol UniRec1 shorts the switch wires, simulating a pushbutton. The output is opto-insulated: maximum admitted current is 30mA and maximum voltage 40Vdc.

{youtube}H0LvWq80GGs|860|560{/youtube}

Creasol UniRec1 can be used to:

  • activate the "start" input of an electronic board used to open/close a gate, garage door, traffic barrier
  • activate an electronic device that is already controlled by remote controls operating in strange or dismessed frequency (418 MHz, 315 MHz, and so on...)
  • enhance the number and type of remote controls that can be used with a gate or garage door opener, by using different brand of existing remote controls even if they transmit in different frequencies.

Using your existing remote control, it's possible for example to:

  1. open your garage door, using the existing electronic board and receiver;
  2. open your gate which uses a different frequency or codings, just installing a Creasol UniRec1 or Creasol UniRec2 receiver connected to it;
  3. open your pedestrian gate, installing a Creasol UniLock device;
  4. open your entrance door, installing a Creasol UniLock device.

The product is made in Europe, provided in a nice transparent resealable recyclable clamshell, with instructions printed in several languages.

We also offer any customization to companies that like to purchase at least 100pcs: please send inquiry by email to sales@creasol.it , specifying company details and special requests.

 

Features

  • Very compact size: 29x29x10mm.

  • Can be supplied  from 5 to 36Vdc and from 7 to 27Vac.

  • Frequency selected by the user: 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8, 315*, 288*, 300*, 303*, 306*, 310*, 318*, 330*, 390*, 403.55*, 418* MHz. Frequencies marked with * cannot be used inside EU. The frequency of the remote control must be stable, so it does not work with remote controls without crystal or saw resonator (some bad remote controls operating around 300 MHz)!

  • OOK (AM) and FSK (FM) modulation is supported: FM with 2 different deviation value, 12,5 and 25 KHz; AM with standard and narrow bandwidth (higher sensitivity)

  • Twin frequency receiver: the user can select one or two frequencies/modulations as preferred, so it can receive, for example, at one single frequency or both 433 MHz OOK and 868 MHz FSK, or both 868MHz OOK and 315MHz OOK, or any combination of frequencies.

  • Works with a wide range of remote controls which transmit fixed or rolling code. See the compatibility table.

  • Manages different types of remote controls in the same time.

  • It's possible to learn one or more "master remote controls" that can be use just to enable learning for 10s without the need to access the receiver to press the Prog button.

 

Documentation

creasolMultiFourRecLock

 

creUniRec1
862 Items

You might also like

Creasol Multi -...

Creasol Multi -...

Regular price €36.23 -32% Price €24.64
  • -32%
Creasol Sender - Stationary multifrequency remote control duplicator

Creasol Sender - Stationary...

Regular price €42.70 -32% Price €29.04
  • -32%
Creasol SenderBatt: 4 channels stationary multifrequency remote control duplicator/transmitter

Creasol SenderBatt: 4...

Regular price €48.80 -32% Price €33.18
  • -32%
creasol UniRec2 -...

creasol UniRec2 -...

Regular price €67.10 -32% Price €45.63
  • -32%
Creasol MultiST, coffee color

Creasol MultiST -...

Regular price €32.94 -32% Price €22.40
  • -32%
Creaso UniRec12 - 2 channels compact multifrequency receiver

Creaso UniRec12 - 2...

Regular price €53.68 -32% Price €36.50
  • -32%
Creasol FourST - 433.92 MHz...

Creasol FourST - 433.92 MHz...

Regular price €23.18 -32% Price €15.76
  • -32%
chat Comments (0)
No customer reviews for the moment.