Volledige ondersteuning: de meeste producten zijn door ons ontworpen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Bestellingen worden binnen 1 werkdag verzonden

Priority mail: snel en goedkoop - Express Courie

24 maanden garantie, eenvoudig retourneren/restitueren

Neem contact met ons op voordat u producten retourneert!

DomBus36 - 12 relais DIN-rail module voor domotica en industriële automatisering

DomBus36 - 12 relais DIN-rail module voor domotica en industriële automatisering

1 Review(s) 

DIN-railmodule met 12 relais, 5A 250V, ondersteunt DomBus- en Modbus RTU-protocollen (te selecteren), voor industriële automatisering en domoticasystemen, zoals Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Zeer laag stroomverbruik, minder dan 750mW met alle 12 relais AAN.

creDomBus36
Protocol: Modbus RTU (compatible with almost any system)
€ 75,64
€ 52,95 - 30%
Inclusief belasting Verzonden in 1 werkdag

Volumekorting

Aantal Eenheidskorting Prijs U bespaart
1 30% € 52,95 € 22,69
2 32% € 51,44 € 48,41
3 33% € 50,68 € 74,88
5 34% € 49,92 € 128,59
Aantal
Beschikbaar

  Volledige ondersteuning: de meeste producten zijn door ons ontworpen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Bestellingen worden binnen 1 werkdag verzonden

Priority mail: snel en goedkoop - Express Courie

  24 maanden garantie, eenvoudig retourneren/restitueren

Neem contact met ons op voordat u producten retourneert!

Creasol DomBus36 is een din-rail relaismodule van industriële kwaliteitvoor gebouwautomatisering en domoticasystemen, 115x90x40mm,met 12 relaisuitgangen,SPST (Normally Open outputs) met 250V 5A max vermogen, verdeeld in 3 groepen van 4 relais, elke groep met 5-positie schroefklemmenblokken: 1 common + 4 outputs

Net als andere DomBus-apparaten,DomBus36 biedt uitstekende prestaties op het gebied van stroomoptimalisatie: 12mW met relais UIT,minder dan 750mW met alle 12 relais AAN!Ter vergelijking: de KMTronic 8-relaismodule verbruikt 12 W, de Denkovi 8-relaiskaart verbruikt ongeveer 3 W, de Sonoff Dual R2 verbruikt 2 W met slechts 2 relais ingeschakeld.

Het is beschikbaar mettwee soorten firmware: DomBus(eigen protocol met verbeterde functies) voor Domoticz-controller,en Modbus RTU(standaardprotocol werkt met vrijwel elk domoticasysteem). Kijk hieronder voor een gedetailleerde vergelijking tussen de twee protocollen.
Het gebruikt eenRS485 seriële bus van industriële kwaliteit, met behulp van een gemeenschappelijke afgeschermde kabel met 4 draden: 2 voor 12/24V voeding en 2 voor data op 115200bps 8,n,1 (of andere snelheid/pariteit in het geval van Modbus RTU).

Het ondersteunt twee verschillende protocollen(op het moment van aankoop,selecteer het benodigde protocol!):

  • DomBus-protocol, dat wordt ondersteund doordomoticadomotica controller,is een betrouwbaar multi-master protocol waarmee tientallen modules kunnen worden beheerd en de status van een module kan worden opgevraagd zodra deze verandert. Het omvat ook de zogenaamdeDCMDcommando's die, vergelijkbaar met KNX, worden verzonden tussen DomBus-modules in dezelfde bus om uitgangen, scènes en groepen te activeren in geval van gebeurtenissen zonder tussenkomst van de domotica-controller, handige oplossing om eendomoticasysteem werkt zelfs in het geval van een storing in de domoticacontroller. Kijk hieronder voor uitleg over DCMD.
    DeCreasolDomBusplug-in moet worden geïnstalleerd in Domoticz, met behulp van dePython-plug-inbeheerof het downloaden van de software vanGitHub(zie het gedeelte hieronder).
  • Modbus RTU-protocol, veel gebruikt in industriële en domoticasystemen, wordt ondersteund door bijna elke domoticacontrollerThuis Assistent,OpenHAB,IOmakelaar,Knooppunt-ROOD, ...
    Modbus is een master-slave-protocol waarmee een enkel relais of een groep relais met een enkel commando kan worden geactiveerd en gedeactiveerd. Het is ook mogelijk om voor elk relais de AAN-tijd van 31,5 ms tot 1500 dagen te specificeren, zodat het relais automatisch UITschakelt na de geselecteerde tijd.

Twijfel je over de twee versies?Als je Domoticz gebruikt,DomBusversieis veel beter omdat het verbeterde functies bevat zoals DCMD en autodiscovery. Voor andere gebouwautomatiseringen, Modbus-versiemoet worden gekozen omdat het compatibel is met bijna alles.
Vraag om ondersteuning opTelegramgroep https://t.me/DomBus

De RS485 seriële bus is de ideale oplossing om:

  • eenvoudige bedrading en aansluiting: gebruik een gemeenschappelijke dunne alarmkabel binnen 4 draden, 2x0.5mm² draden voor 12V voeding, en 2x0.22mm² draden voor data. Dit is veel gemakkelijker en beter dan ethernet UTP/STP-verbindingen.
  • robuustheid differentiële signaleringmaakt het mogelijk om ongeveer 30 modules aan te sluiten met een totale afstand van meer dan 200 meter. Modules kunnen met elkaar worden verbonden met behulp van een mix van lineaire/sterbus-topologie.
  • zeer laag stroomverbruik: elke module wordt geleverd op 12V en heeft een zeer efficiënte schakelende omvormer om het stroomverbruik te minimaliseren.
  • stroomuitval tolerant: met behulp van een 13,6V-voeding met loodzuurbatterij is het mogelijk om domoticanetwerken, IPCams, NVR's, schakelaars, routers te voeden, zodat het systeem blijft werken, zelfs in geval van stroomuitval.
  • geen RF-vervuiling, geen batterijen om te vervangen

Voor grote gebouwen is het, om de betrouwbaarheid van de bus te verbeteren, mogelijk om meer dan 1 bus te maken, dus in geval van storing stopt alleen de bus met storing.

Functies

  • beschikbaar in twee firmwareversies,DomBusgeschikt voor Domoticz controller, en Modbus geschikt voorelk industrieel en domoticasysteem.
  • 12 relaisuitgangen, SPST (normaal open contact op schroefklemmenblok) met 250Vac/30Vdc 5A contact (max. 30Vdc bij DC-belasting, 250Vac bij AC-belasting).
  • eenvoudige bedrading : relais zijn verdeeld in 3 groepen, elke groep deelt een gemeenschappelijke met de 4 relais in die groep .
  • elk relaisblok respecteert de kruipafstand van andere blokken. Meng geen hoog- en laagspanningssignalen binnen hetzelfde blok!
  • 8-35Vdc voeding (intern geregeld door een geschakelde voedingschakeling die stroomverbruik en dissipatie minimaliseert).
  • laag stroomverbruik: 0.9mA @12V ( 12mW ) stand-by stroom met alle relais UIT, en 55mA @12V (< 750mW ) met alle relais AAN .
  • 115200 bps RS485-bus (max. lengte: 1 km), 8 bit data, geen pariteit, 1 stopbit. Bitrate en pariteit kunnen worden gewijzigd in de Modbus-versie.
  • Ondersteuning voor DCMD- commando's (alleen DomBus-firmware): dit is een functie (hieronder beschreven) die het mogelijk maakt om eenvoudige automatiseringen te krijgen zonder een regel code te schrijven, en commando's uit te wisselen tussen DomBus-modules, zelfs als de domoticacontroller is gestopt . Bijvoorbeeld het configureren van een drukknopinvoerpoort als
    DCMD(Puls)=11.3:Schakelen, DCMD(Puls1)=0.7:Schakelen, DCMD(Puls2)=0.8:Aan
    het is mogelijk:
    * met een korte0,5s puls, schakelt poort #3 output van DomBus module #11 aan/uit
    * schakel met een puls van 1s een groep schakelaars op de controller aan/uit
    * activeer met een 2s lange puls een scene die bijvoorbeeld alle lampen/verbruikers uitschakelt en het alarmsysteem activeert (handig bij het verlaten van het gebouw).

Waarschuwingen

  • Relais zijn verdeeld in 3 blokken:combineer geen hoogspanningsbelastingen (230V) en laagspanningsbelastingen (5/12/24V) op hetzelfde klemmenblok!
  • Gebruik nietcapacitieve belastingen met hoge inschakelstroom(slechte voedingen, voorschakelapparaten, ...) anders kan het relaiscontact vastlassen.
  • Gebruik een4-aderige afgeschermde kabel voor de bus, met behulp van twee regels om te verzendenvoeding (12-14Vdc) beveiligd door een zekering.
  • Om geluid en reflecties op de bus te verminderen,schakel de afsluitweerstand in(kortsluiting Rbus PCB-jumper)aan de twee verste uiteinden van de bus.

Meer informatie ophttps://www.creasol.it/DomBus36




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus36

Reviews

Grade 
Peter Hockradl

Smart!

Sehr clevere Idee, Gruppen von 4 Ausgängen gemeinsam zu nutzen! Einfache Verkabelung.
Modulverbrauch ist wie angegeben wirklich niedrig.
Zufrieden.

Write your review

DomBus36 - 12 relais DIN-rail module voor domotica en industriële automatisering

DIN-railmodule met 12 relais, 5A 250V, ondersteunt DomBus- en Modbus RTU-protocollen (te selecteren), voor industriële automatisering en domoticasystemen, zoals Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Zeer laag stroomverbruik, minder dan 750mW met alle 12 relais AAN.

Write your review

Je bent misschien ook geïnteresseerd in

Klanten die dit product aangeschaft hebben kochten ook...

DomBus36 - 12 relais...

€ 75,64 € 52,95