Volle Unterstützung: Die meisten Produkte werden von uns entworfen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Bestellungen werden innerhalb eines Werktages versandt

Priority Mail: schnell und günstig – Exp

24 Monate Garantie, einfache Rückgabe/Rückerstattung

Kontaktieren Sie uns, bevor Sie Produkte zur

DomBus36 - 12-Relais-DIN-Schienenmodul für Heim- und Industrieautomation

DomBus36 - 12-Relais-DIN-Schienenmodul für Heim- und Industrieautomation

1 Review(s) 

DIN-Schienenmodul mit 12 Relais, 5 A 250 V, unterstützt die Protokolle DomBus und Modbus RTU (auszuwählen), für industrielle Automatisierungs- und Heimautomatisierungssysteme, wie Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Sehr geringer Stromverbrauch, weniger als 750 mW, wenn alle 12 Relais eingeschaltet sind.

creDomBus36
Protocol: Modbus RTU (compatible with almost any system)
75,64 €
52,95 € - 30%
Bruttopreis Versand innerhalb von 1 Werktag

Mengenrabatt

Menge Rabatt auf Stückzahl Preis Sie sparen
1 30% 52,95 € 22,69 €
2 32% 51,44 € 48,41 €
3 33% 50,68 € 74,88 €
5 34% 49,92 € 128,59 €
Menge
Erhältlich

  Volle Unterstützung: Die meisten Produkte werden von uns entworfen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Bestellungen werden innerhalb eines Werktages versandt

Priority Mail: schnell und günstig – Exp

  24 Monate Garantie, einfache Rückgabe/Rückerstattung

Kontaktieren Sie uns, bevor Sie Produkte zur

Creasol DomBus36 ist ein industrietaugliches DIN-Schienen-Relaismodulfür Gebäudeautomation und Hausautomation, 115x90x40mm,mit 12 Relaisausgängen,SPST (Normally Open Outputs) mit 250 V 5 A max. Kapazität, aufgeteilt in 3 Gruppen mit 4 Relais, jede Gruppe mit Schraubklemmenblöcken mit 5 Positionen: 1 gemeinsame + 4 Ausgänge

Wie andere DomBus-Geräte,DomBus36 bietet eine hervorragende Leistung in Bezug auf die Leistungsoptimierung: 12 mW mit Relais AUS,weniger als 750 mW mit allen 12 Relais EIN!Zum Vergleich: KMTronic 8-Relais-Modul verbraucht 12 W, Denkovi 8-Relais-Platine verbraucht etwa 3 W, Sonoff Dual R2 verbraucht 2 W, wenn nur 2 Relais aktiviert sind.

Es ist erhältlich mitzwei Firmware-Typen: DomBus(proprietäres Protokoll mit erweiterten Funktionen) für Domoticz-Controller,und Modbus-RTU(Standardprotokoll, das mit fast jedem Hausautomationssystem funktioniert). Unten finden Sie einen detaillierten Vergleich zwischen den beiden Protokollen.
Es verwendet aSerieller RS485-Bus in Industriequalität, unter Verwendung eines gemeinsamen abgeschirmten Kabels mit 4 Drähten: 2 für die 12/24-V-Stromversorgung und 2 für Daten mit 115200 bps 8,n,1 (oder einer anderen Geschwindigkeit/Parität im Fall von Modbus RTU).

Es unterstützt zwei verschiedene Protokolle(zum Zeitpunkt des Kaufs,Wählen Sie das benötigte Protokoll aus!):

  • DomBus-Protokoll, das wird unterstützt vonDomoticzHeimautomatisierungscontroller,ist ein zuverlässiges Multi-Master-Protokoll, das es ermöglicht, Dutzende von Modulen zu verwalten und den Status eines Moduls abzurufen, sobald es sich ändert. Dazu gehören auch die sogDCMDBefehle, die ähnlich wie bei KNX zwischen DomBus-Modulen im selben Bus übertragen werden, um bei Ereignissen Ausgänge, Szenen und Gruppen zu aktivieren, ohne dass der Hausautomationscontroller eingreifen muss, eine nützliche Lösung, um eineDas Hausautomationssystem funktioniert auch bei einem Fehler des Domotik-Controllers. Unten finden Sie eine Erklärung zu DCMD.
    DerKreasolDomBusPlugin muss in Domoticz installiert werden, mit demPython-Plugin-Manageroder Herunterladen der Software vonGitHub(siehe Abschnitt unten).
  • Modbus RTU-Protokoll, weit verbreitet in Industrie- und Heimautomatisierungssystemen, wird von fast jedem Domotik-Controller wie unterstütztHeimassistent,OpenHAB,IObroker,Knoten-ROT, ...
    Modbus ist ein Master-Slave-Protokoll, das es ermöglicht, ein einzelnes Relais oder eine Gruppe von Relais durch einen einzigen Befehl zu aktivieren und zu deaktivieren. Außerdem ist es möglich, für jedes Relais die EIN-Zeit von 31,5 ms bis 1500 Tagen festzulegen, sodass das Relais nach der ausgewählten Zeit automatisch ausschaltet.

Verwirrt über die beiden Versionen?Wenn Sie Domoticz verwenden,DomBusAusführungist viel besser, da es erweiterte Funktionen wie DCMD und Autodiscovery enthält. Für andere Gebäudeautomatisierungen Modbus-Versionsollte gewählt werden, weil es mit fast allem kompatibel ist.
Bitten Sie um Unterstützung aufTelegrammgruppe https://t.me/DomBus

Der serielle RS485-Bus ist die ideale Lösung, um Folgendes zu erreichen:

  • einfache Verdrahtung und Anschluss: Verwenden Sie ein gemeinsames dünnes Alarmkabel mit 4 Drähten, 2 x 0,5 mm² Drähte für die 12-V-Stromversorgung und 2 x 0,22 mm² Drähte für Daten. Dies ist viel einfacher und besser als Ethernet-UTP/STP-Verbindungen.
  • Robustheit differentielle Signalisierungermöglicht die Verbindung von etwa 30 Modulen mit mehr als 200 m Gesamtlänge. Module können unter Verwendung einer Mischung aus linearer/sternförmiger Bustopologie miteinander verbunden werden.
  • sehr geringer Stromverbrauch: Jedes Modul wird mit 12 V versorgt und verfügt über einen hocheffizienten Schaltwandler, um den Stromverbrauch zu minimieren.
  • stromausfalltolerant: Mit einem 13,6-V-Netzteil mit Blei-Säure-Batterie ist es möglich, Domotik-Netzwerke, IPCams, NVR, Switches, Router zu versorgen, sodass das System auch bei Stromausfall weiter funktioniert.
  • keine HF-Verschmutzung, kein Batteriewechsel

Bei großen Gebäuden ist es zur Verbesserung der Buszuverlässigkeit möglich, mehr als 1 Bus zu verwenden, damit im Falle einer Störung nur der Bus mit der Störung nicht mehr funktioniert.

Merkmale

  • verfügbar in zwei Firmware-Versionen,DomBusgeeignet für Domoticz-Controller und Modbus passend fürjedes Industrie- und Hausautomationssystem.
  • 12 Relaisausgänge, SPST (normalerweise offener Kontakt auf Schraubklemmenblock) mit 250 Vac/30 Vdc 5 A Kontakt (max. 30 Vdc bei DC-Last, 250 Vac bei AC-Last).
  • Einfache Verdrahtung : Die Relais sind in 3 Gruppen unterteilt, jede Gruppe teilt sich eine Gemeinsamkeit mit den 4 Relais in dieser Gruppe .
  • jeder Relaisblock respektiert die Kriechstrecke von anderen Blöcken. Mischen Sie keine Hoch- und Niederspannungssignale innerhalb desselben Blocks!
  • 8–35-V-Gleichstromversorgung (intern geregelt durch eine Schaltnetzteilschaltung, die den Stromverbrauch und die Verlustleistung minimiert).
  • Geringer Stromverbrauch: 0,9 mA bei 12 V ( 12 mW ) Standby- Strom, wenn alle Relais AUS sind, und 55 mA bei 12 V (< 750 mW ), wenn alle Relais EIN sind .
  • 115200 bps RS485-Bus (max. Länge: 1 km), 8-Bit-Daten, keine Parität, 1 Stoppbit. Bitrate und Parität können in der Modbus-Version geändert werden.
  • DCMD- Befehlsunterstützung (nur DomBus-Firmware): Dies ist eine Funktion (unten beschrieben), die es ermöglicht, einfache Automatisierungen zu erhalten, ohne eine Codezeile zu schreiben, und Befehle zwischen DomBus-Modulen auszutauschen, selbst wenn der Domotik-Controller gestoppt ist . Konfigurieren Sie beispielsweise einen Drucktasten-Eingangsport als
    DCMD (Impuls) = 11,3: Umschalten, DCMD (Impuls 1) = 0,7: Umschalten, DCMD (Impuls 2) = 0,8: Ein
    es ist möglich:
    * mit einem kurzen0,5-s-Impuls, schaltet den Ausgang von Port Nr. 3 des DomBus-Moduls Nr. 11 ein/aus
    * Schalten Sie mit einem 1s-Impuls eine Gruppe von Schaltern auf dem Controller ein/aus
    * Aktivieren Sie mit einem 2s langen Impuls eine Szene, die beispielsweise alle Lichter/Lasten deaktiviert und die Alarmanlage aktiviert (nützlich beim Verlassen des Gebäudes).

Warnungen

  • Relais sind in 3 Blöcke unterteilt:Mischen Sie keine Hochspannungslasten (230 V) und Niederspannungslasten (5/12/24 V) an derselben Klemmenleiste!
  • Verwende nichtkapazitive Lasten mit hohem Einschaltstrom(schlechte Netzteile, Vorschaltgeräte, ...) sonst kann der Relaiskontakt verschweißen.
  • Benutze einen4-adriges geschirmtes Kabel für den Bus, wobei zwei Zeilen zum Senden verwendet werdenStromversorgung (12-14Vdc) durch eine Sicherung geschützt.
  • Um Lärm und Reflexionen im Bus zu reduzieren,Abschlusswiderstand aktivieren(Rbus PCB-Jumper kurzschließen)an den beiden äußersten Enden des Busses.

Mehr Informationen beihttps://www.creasol.it/DomBus36




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus36

Reviews

Grade 
Peter Hockradl

Smart!

Sehr clevere Idee, Gruppen von 4 Ausgängen gemeinsam zu nutzen! Einfache Verkabelung.
Modulverbrauch ist wie angegeben wirklich niedrig.
Zufrieden.

Write your review

DomBus36 - 12-Relais-DIN-Schienenmodul für Heim- und Industrieautomation

DIN-Schienenmodul mit 12 Relais, 5 A 250 V, unterstützt die Protokolle DomBus und Modbus RTU (auszuwählen), für industrielle Automatisierungs- und Heimautomatisierungssysteme, wie Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ...
Sehr geringer Stromverbrauch, weniger als 750 mW, wenn alle 12 Relais eingeschaltet sind.

Write your review

Vielleicht gefällt Ihnen auch

Kunden, die diesen Artikel gekauft haben, kauften auch ...

DomBus36 -...

75,64 € 52,95 €