DomBus36 - 12 releju DIN-sliedes modulis mājas un rūpniecības automatizācijai
1 Review(s) 
DIN sliedes modulis 12 relejos, 5A 250V, atbalsta DomBus un Modbus RTU protokolus (jāizvēlas), rūpnieciskajai automatizācijai un mājas automatizācijas sistēmām, piemēram, Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ... Ļoti zems enerģijas patēriņš, mazāk nekā 750 mW ar IESLĒGTIEM 12 relejiem.
Pilns atbalsts: lielāko daļu produktu izstrādājam mēs!
Creasol DomBus36 ir din-rail releja rūpnieciskas klases modulisēku automatizācijai un mājas automatizācijas sistēmām, 115x90x40mm,ar 12 releju izejām,SPST (parasti atvērtas izejas) ar 250V 5A max jaudu, sadalītas 3 grupās pa 4 relejiem, katra grupa ar 5 pozīciju skrūvju spaiļu blokiem: 1 kopējā + 4 izejas
Tāpat kā citas DomBus ierīces,DomBus36 nodrošina izcilu veiktspēju jaudas optimizācijas ziņā: 12mW ar izslēgtiem relejiem,mazāk par 750mW ar IESLĒGTIEM 12 relejiem!Salīdzinājumam, KMTronic 8 releju modulis patērē 12W, Denkovi 8 releju plate patērē apmēram 3W, Sonoff Dual R2 patērē 2W ar iespējotiem tikai 2 relejiem.
Tas ir pieejams ardivi programmaparatūras veidi: DomBus(patentēts protokols ar uzlabotām funkcijām) Domoticz kontrollerim,un Modbus RTU(standarta protokols, kas darbojas gandrīz ar jebkuru mājas automatizācijas sistēmu). Tālāk skatiet detalizētu abu protokolu salīdzinājumu. Tas izmanto aRS485 rūpnieciskā līmeņa seriālā kopne, izmantojot kopīgu ekranētu kabeli ar 4 vadiem: 2 12/24V barošanas avotam un 2 datiem 115200bps 8,n,1 (vai citu ātrumu/paritāti Modbus RTU gadījumā).
Tā atbalsta divus dažādus protokolus(pirkšanas laikā,izvēlieties vajadzīgo protokolu!):
DomBus protokols, ko atbalstaDomotičsmājas automatizācijas kontrolieris,ir uzticams vairāku galveno protokolu protokols, kas ļauj pārvaldīt desmitiem moduļu un iegūt statusu no moduļa, tiklīdz tas mainās. Tas ietver arī tā sauktoDCMDkomandas, kuras, līdzīgi kā KNX, tiek pārraidītas starp DomBus moduļiem vienā kopnē, lai notikumu gadījumā aktivizētu izejas, ainas un grupas bez mājas automatizācijas kontrollera iejaukšanās, noderīgs risinājums, lai iegūtumājas automatizācijas sistēma darbojas pat domotiskā kontrollera kļūmes gadījumā. Tālāk skatiet skaidrojumu par DCMD. TheCreasolDomBusspraudnis ir jāinstalē Domoticz, izmantojotPython spraudņu pārvaldnieksvai lejupielādējot programmatūru noGitHub(skatiet sadaļu zemāk).
Modbus RTU protokols, ko plaši izmanto rūpnieciskās un mājas automatizācijas sistēmās, atbalsta gandrīz jebkurš domotic kontrolieris, piemēramMājas palīgs,OpenHAB,IObrokeris,Mezgls-SARKANS,... Modbus ir galvenā-pakalpojuma protokols, kas ļauj aktivizēt un deaktivizēt vienu releju vai releju grupu ar vienu komandu. Turklāt katram relejam ir iespējams norādīt IESLĒGŠANAS laiku no 31,5 ms līdz 1500 dienām, lai pēc izvēlētā laika relejs automātiski izslēgtos.
Vai esat apmulsis par abām versijām?Ja lietojat Domoticz,DomBusversijair daudz labāks, jo ietver tādas uzlabotas funkcijas kā DCMD un automātiskā atklāšana. Citai ēku automatizācijai Modbus versijajāizvēlas, jo saderīgs ar gandrīz visu. Lūdziet atbalstu vietnēTelegram grupa https://t.me/DomBus
RS485 seriālā kopne ir ideāls risinājums, lai iegūtu:
vienkārša elektroinstalācija un savienojums: izmantojiet parastu plānu trauksmes vadu 4 vados, 2 x 0,5 mm² vadus 12 V strāvas padevei un 2 x 0,22 mm² vadus datiem. Tas ir daudz vienkāršāk un labāk nekā Ethernet UTP/STP savienojumi.
robustuma diferenciālā signalizācijaļauj savienot aptuveni 30 moduļus ar kopējo attālumu vairāk nekā 200m. Moduļus var savienot kopā, izmantojot lineāro/zvaigžņu kopnes topoloģiju.
ļoti zems enerģijas patēriņš: katrs modulis tiek piegādāts ar 12 V spriegumu, un tajā ir iebūvēts augstas efektivitātes pārslēgšanas režīma pārveidotājs, lai samazinātu enerģijas patēriņu.
izturīgs pret strāvas padevi: izmantojot 13.6V barošanas bloku ar svina skābes akumulatoru, iespējams nodrošināt domotisko tīklu, IPC kameras, NVR, slēdžus, maršrutētājus, lai sistēma darbotos arī strāvas padeves pārtraukuma gadījumā.
nav RF piesārņojuma, nav jāmaina baterijas
Lielai ēkai, lai uzlabotu autobusa uzticamību, ir iespējams izgatavot vairāk nekā 1 autobusu, tāpēc bojājuma gadījumā pārstāj darboties tikai autobuss ar defektu.
Iespējas
pieejams divās programmaparatūras versijās,DomBuspiemērots Domoticz kontrolierim un Modbus piemērotsjebkura rūpniecības un mājas automatizācijas sistēma.
12 releju izejas, SPST (parasti atvērts kontakts uz skrūvju spaiļu bloka) ar 250Vac/30Vdc 5A kontaktu (maks. 30Vdc līdzstrāvas slodzes gadījumā, 250Vac maiņstrāvas slodzes gadījumā).
vienkārša elektroinstalācija : releji ir sadalīti 3 grupās, katrai grupai ir kopīgs 4 releji šajā grupā .
katrs releja bloks ievēro šļūdes attālumu no citiem blokiem. Nejauciet augsta un zemsprieguma signālus vienā blokā!
8–35 V līdzstrāvas barošanas avots (iekšēji regulē komutācijas režīma barošanas avota shēma, kas samazina enerģijas patēriņu un izkliedi).
zems enerģijas patēriņš: 0,9 mA pie 12 V ( 12 mW ) gaidstāves strāva ar izslēgtiem relejiem un 55 mA @ 12 V (< 750 mW ), kad visi releji ir IESLĒGTI .
115200 bps RS485 autobuss (maksimālais garums: 1km), 8 bitu dati, bez paritātes, 1 pieturas bits. Bitu pārraides ātrums un paritāte var tikt mainīti Modbus versijā.
DCMD komandu atbalsts (tikai DomBus programmaparatūrai): šī ir funkcija (aprakstīta zemāk), kas ļauj iegūt vienkāršu automatizāciju, neierakstot koda rindiņu, un komandu apmaiņu starp DomBus moduļiem pat gadījumā, ja domotic kontrolleris tiek apturēts . Piemēram, konfigurējot spiedpogu ievades portu kā DCMD(impulss)=11,3: pārslēgt, DCMD(impulss1)=0,7: pārslēgt, DCMD(impulss2)=0,8: ieslēgts tas ir iespējams: * ar īsu0,5 s impulss, ieslēdz/izslēdz DomBus moduļa #11 portu #3 * ar 1 s impulsu ieslēdziet/izslēdziet kontrollera slēdžu grupu * ar 2s garu impulsu aktivizēt ainu, kas, piemēram, atspējo visas gaismas/slodzes un aktivizē signalizāciju (noder, izejot no ēkas).
Brīdinājumi
Releji ir sadalīti 3 blokos:nejauc augstsprieguma (230V) slodzes un zemsprieguma (5/12/24V) slodzes uz viena spaiļu bloka!
Nelietojietkapacitatīvās slodzes ar lielu ieslēgšanas strāvu(slikti barošanas avoti, balasti, ...) pretējā gadījumā releja kontakts var sametināt.
Lieto4 vadu ekranēts kabelis autobusam, izmantojot divas rindiņas, lai nosūtītubarošanas avots (12-14Vdc), kas aizsargāts ar drošinātāju.
Lai samazinātu troksni un atspulgus autobusā,iespējot beigu rezistoru(īssavienojošs Rbus PCB džemperis)abos autobusa tālākajos galos.
Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
very low power (around 10mW with relays OFF)
reliable (no disconnections)
bus connected (no radiofrequency interference, no battery to replace).
Modules are available in two version:
with DomBus proprietary protocol, working with Domoticz only
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Single-phase and three-phases, up to 36A (8kW or 22kW)
Needs external contactor, RCCB (protection) and EV cable
Optional power meter to measure charging power, energy, voltage and power factor
Optional power meter to measure the power usage from the grid (not needed if already exists)
Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)
DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
temperature and relative humidity sensor
red, green and white LEDs
4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.
DomBus12 - Compact domotic module with 9 I/Os
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
analog/digital inputs
pushbutton and UP/DOWN pushbutton
counters (water, gas, S0 energy, ...)
NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.
DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
3x high power latching relays SPST 15A: latching relay consumes nothing when ON
1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...
DomBus23 - Domotic module with many functions
Versatile module designed to control gate or garage door.
2x relays SPST 5A
1x 10A 30V mosfet (led stripe dimming)
2x 0-10V analog output: each one can be configured as open-drain output to control external relay
DIN rail low profile module, with 8 relays and very low power consumption:
6x relays SPST 5A
2x relays STDT 10A
Only 10mW power consumption with all relays OFF
Only 500mW power consumption with all 8 relays ON !!
DomBus32 - Domotic module with 3 relays
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
DomBus33 - Module to domotize a light system using step relays
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DomBus36 - Domotic module with 12 relays
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
12x relays SPST 5A
Relays are grouped in 3 blocks, with a single common per block, for easier wiring
Only 12mW power consumption with all relays OFF
Only 750mW power consumption with all 12 relays ON !!
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
3x 115/230Vac optoisolated inputs
2x relays SPST 5A
1x relay SPST 10A
DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs
DIN rail module designed for burglar alarm system.
4x relays SPDT (normally open + close contacts), 10A
2x relays SPST 10A
1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
Works in stand-alone mode (no need for external controller)
Can be connected to Domoticz for monitoring and controlling the motors position
DomRelay2 - 2x relays board
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
2x 5A 12V SPST relays (Normally Open contact)
Overvoltage protection (for inductive loads, like motors)
Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)
DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
9-24V input voltage, with high efficiency DC/DC regulator with 5V output
4x SPST relays 5V with overvoltage protection
1x SSR output (max 40V output)
2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
1x I²C interface for sensors, extended I/Os and more)
1x OneWire interface (DS18B20 or other 1wire sensors/devices)
DIN sliedes modulis 12 relejos, 5A 250V, atbalsta DomBus un Modbus RTU protokolus (jāizvēlas), rūpnieciskajai automatizācijai un mājas automatizācijas sistēmām, piemēram, Domoticz, Home Assistant, OpenHAB, ioBroker, Node-RED, ... Ļoti zems enerģijas patēriņš, mazāk nekā 750 mW ar IESLĒGTIEM 12 relejiem.