
Creasol DomBusTH - Domoticz apparaat met temperatuur- en vochtigheidssensoren, 4 ingangen, 2 uitgangen, 3 leds
- Aanbieding!
- -30%
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: snel en goedkoop - Express Courie
Neem contact met ons op voordat u producten retourneert!
Dit is een pakket met 3x relaismodules DomRelay2 (3 stuks)
Compacte module, 43x24x25mm, binnen2 relais met 12Vdc 200mW spoel, 250V 5A SPST contact.
Contacten zijnbeschermd tegen overstroom en overspanning
Geschikt om te worden aangesloten op domoticasystemen zoals Creasol DomBus-modules: inderdaad,gebruik makend vanDomBusTHofDomBus12modules is het mogelijk om relais aan te sturen met een systeem met een lager vermogen, dat minder dan 1/4 van het nominale vermogen verbruikt
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority mail: snel en goedkoop - Express Courie
Neem contact met ons op voordat u producten retourneert!
Creasol DomRelay2 is een compacte module, 43x24x25mm, binnenin2 relais met 12V 200mW spoel, 250V 5A SPST contactmet speciaal materiaal ontworpen omvoorkom contactlassendoor te hoge stootstroombelasting (capacitieve belastingen of wolfraamlampen).
Contacten zijnbeschermd tegen overspanningdoor metaaloxidevaristoren; spoelen worden tegen overspanning beschermd door vrijloopdiodes.
De relaisspoel moet worden aangedreven met 12Vdc 17mA:gebruik makend vanDomBusTHofDomBus12modules is het mogelijk om relais aan te sturen met een systeem met een lager vermogen, dat minder dan 1/4 van het nominale vermogen verbruikt
Sluit het 12V-klemmenblok aan op de voeding 12Vdc.
Verbind elke relaisingang met een module-uitgang die de lijn naar aarde trekt, zoals een open-collector- of open-drain-uitgang.
Bijvoorbeeldhet is mogelijk om deze relaismodule langs te rijdenDomBusTHen DomBus12, RS485 / Modbus-modules voor Domoticz die ook een handige functie hebben die het mogelijk maakt om het stroomverbruik van het relais drastisch te verminderen tot ongeveer 1/4 van het nominale spoelvermogen
DomBusTHikeen domoticamodule met temperatuur- / vochtigheidssensor, 3 leds, 4 I / O's en 2 open-drain uitgangen.
De open-drain uitgangen zijn geschikt om relaisspoelen aan te sturen, zodat ze op deDomRelay2module om bijvoorbeeld een rolluikmotor aan te sturen om rolluiken / jaloezieën / gordijnen te openen / sluiten.
EvenzoDomBus12is een andere domotica-module met 7 I / O's en 2 open-drain uitgangen, die ook geschikt zijn om een relaismodule aan te sturen alsDomRelay2
BeideDomBusTHen DomBus12hebben een handige functie die het mogelijk maakt om het stroomverbruik van het relais drastisch te verminderen tot ongeveer 1/4 van het nominale spoelvermogen.
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller