Suport complet: majoritatea produselor sunt concepute de noi!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Comenzile sunt expediate în termen de 1 zi lucrătoare

Poștă prioritară: rapid și ieftin - Curie

24 de luni garanție, returnare/rambursare ușoară

Contactați-ne înainte de a returna produsele!

Creasol DomBus23: modul Smart Home cu 2 relee, 1x mosfet, ...

Creasol DomBus23: modul Smart Home cu 2 relee, 1x mosfet, ...

1 Review(s) 

Creasol DomBus23 este un modulpentru sistemul de automatizare a caseicu mai multe tipuri diferite de intrări / ieșiriîntr-o dimensiune scurtă: 74x72x24mm. p>

Poate fi conectat la controlerul Domoticz printr-o magistrală serială RS485 (4 fire, 2 pentru sursa de alimentare 12 / 24V și 2 pentru date la 115200bps).

Ca și alte dispozitive DomBus,DomBus23 este conceput pentru a consuma energie redusă, pentru a fi fiabil, complet configurabil și ușor de utilizat.

creDomBus23
Protocol: Modbus RTU (compatible with almost any system)
53,68 €
37,58 € - 30%
Include TVA Livrat in 1 zi lucratoare

Reduceri la volum

Cantitate Reducere de cantitate Pret Ai economisit
1 30% 37,58 € 16,10 €
2 32% 36,50 € 34,36 €
3 34% 35,43 € 54,75 €
4 35% 34,89 € 75,15 €
6 36% 34,36 € 115,95 €
9 37% 33,82 € 178,75 €
Cantitate
Disponibil

  Suport complet: majoritatea produselor sunt concepute de noi!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Comenzile sunt expediate în termen de 1 zi lucrătoare

Poștă prioritară: rapid și ieftin - Curie

  24 de luni garanție, returnare/rambursare ușoară

Contactați-ne înainte de a returna produsele!

Creasol DomBus23 este un modulpentru sistemul de automatizare a caseicu mai multe tipuri diferite de intrări / ieșiriîntr-o dimensiune scurtă: 74x72x24mm. p>

Poate fi conectat la controlerul de automatizare a locuinței printr-o magistrală serial RS485 (4 fire, 2 pentru sursa de alimentare 12 / 24V și 2 pentru date la 115200bps).

Controlerele de sisteme de automatizare a locuinței acceptate suntDomoticz.

Ca și alte dispozitive DomBus,DomBus23 este conceput pentru a consuma energie redusă, pentru a fi fiabil, complet configurabil și ușor de utilizat.

Creasol DomBus23 smart home module for Domoticz, ...

p>

puternic>

Caracteristici

  • 2 releu SPSTieșiri, 250Vac 5A, care pot fi configurate în modul de putere redusă pentru a minimiza consumul de energie (mai puțin de 70mW / releu, în loc de 200mW / releu) și în modul OUT_BLIND pentru a acționa un motor cu rulou
  • 1 ieșire MOSFET, 30V 10A max, cuatât funcții digitale, cât și funcții de estompare, care poate fi folosit pentru a conducebandă cu led care reglează luminozitatea
  • 2 ieșire analogică 0-10V(poate fi utilizat pentru a controla alte plăci electronice cu intrare 0-10V, cum ar fi variatoarele): fiecare poate fi configurat caieșire de golire deschisă (disponibilă prin cablul opțional)în cazul în care ieșirea analogică 0-10V este inutilă
  • 2 I / Olines, fiecare poate fi configurat ca intrare digitală, intrare analogică, buton dublu, contor (pentru contoare de energie sau gaze), ieșire digitală, orb, dimmer (pentru a fi conectat la un mosfet extern) și buzzer (buzzer piezo conectat la cele două linii , în configurație push-pull). li>
  • 2 intrări de joasă tensiune AC / DC optoizolate, 9-40V
  • 1 intrare 230V AC optoizolată
  • Sursă de alimentare de 7,5-35 Vcc (reglată intern de un circuit de alimentare cu regim de comutare care minimizează consumul și disiparea de energie)
  • consum redus de energie: 10mWașteptareputere
  • Autobuz RS485 de 115200 bps (lungime maximă: 1 km)

Mai multe informații la https://www.creasol.it/CreasolDomBus23

Capabilități Porturi DomBus23

Adresă implicită: 0xff23

Port# Nume Capacități Configurare implicită Descriere
1 RL1 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP Ieșire releu SPST, cu o rată de contact 250Vac 5A sau o rată de contact 30Vdc 5A. Contactul releului este protejat de supratensiune prin varistor
2 RL2 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP Ieșire releu SPST, cu o rată de contact 250Vac 5A sau o rată de contact 30Vdc 5A. Contactul releului este protejat de supratensiune prin varistor
3 MOS OUT_DIGITAL, OUT_DIMMER OUT_DIMMER Ieșire cu evacuare deschisă Mosfet, 30V 12A max, adecvată pentru controlul benzilor cu led (cu posibilitatea de a regla luminozitatea utilizând funcția de estompare DomBus, 0-100% cu 5% pas) sau alte sarcini DC.
4 V1 / OD1 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_ANALOG

Ieșire analogică, 0-10V, adecvată pentru a controla intrarea 0-10V sau 1-10V a unei alte plăci electronice (regulator, pompă de căldură, supapă liniară, ...).
Opțional, este posibil să configurați acest port ca ieșire open-drain 40V 100mA max, care poate fi conectat la leduri externe sau releu utilizând cablul opțional cu 5 fire:od1jumperul PCB trebuie scurtcircuitat, în acest caz.

5 V2 / OD2 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND(1) OUT_ANALOG Ieșire OAnalogică, 0-10V, adecvată pentru controlul intrării 0-10V sau 1-10V a unei alte plăci electronice (regulator, pompă de căldură, supapă liniară, ...).
Opțional, este posibil să configurați acest port ca ieșire open-drain 40V 100mA max, care poate fi conectat la leduri externe sau releu utilizând cablul opțional cu 5 fire:od2jumperul PCB trebuie scurtcircuitat, în acest caz.
6 IO1 IN_DIGITAL,IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER IN_DIGITAL

Intrare analogică / digitală care poate fi utilizată pentru citirea tensiunilor sau poate fi conectată la contact, comutator, senzor magnetic, PIR, ...
Poate fi configurat ca contor și conectat la contorul de energie / gaz / apă.
Poate fi configurat ca IN_TWINBUTTON (care poate fi conectat la un buton dublu) prin scurtcircuitarea jumperului PCBRU1sau 10mA OUTPUT prin scurtcircuitarea jumperului PCBRO1: în acest din urmă caz, poate fi utilizat ca o ieșire de curent redus de 3V, conectat la buzzer sau la o placă de releu din driverul bobinei.

7 IO2 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND(1), OUT_DIMMER, OUT_BUZZER IN_DIGITAL Intrare analogică / digitală care poate fi utilizată pentru citirea tensiunilor sau poate fi conectată la contact, comutator, senzor magnetic, PIR, ...
Poate fi configurat ca contor și conectat la contorul de energie / gaz / apă.
Poate fi configurat ca IN_TWINBUTTON (care poate fi conectat la un buton dublu) prin scurtcircuitarea jumperului PCBRU2sau 10mA OUTPUT prin scurtcircuitarea jumperului PCBRO2: în acest din urmă caz, poate fi utilizat ca o ieșire de curent redus de 3V, conectat la buzzer sau la o placă de releu din driverul bobinei.
8 ÎN 1 IN_AC IN_AC, IN_COUNTER Intrare de joasă tensiune, 9-40V AC sau DC, optoizolată. Potrivit pentru a simți prezențaVoltaj
9 IN2 IN_AC IN_AC, IN_COUNTER Intrare de joasă tensiune, 9-40V AC sau DC, optoizolată. Potrivit pentru a simți prezența tensiunii
10 IN3 IN_AC IN_AC, IN_COUNTER Intrare 230V, optoizolată. Potrivit pentru a detecta prezența tensiunii și pentru a detecta întreruperea curentului (întrerupere)

(1): poate fi folosit ca ieșire BLIND, pentru a deschide un blind / cortină, dar numai portul anterior poate fi configurat în Domoticz ca OUT_BLIND deoarece, atunci când este configurat ca OUT_BLIND, dispozitivul DomBus configurează automat următorul port pentru a conduce un releu în deschidere direcţie.

Note de aplicare

Dimming 1 bandă cu led de Mosfet intern 24V 12A, + 2 benzi cu LED folosind controler extern

Modulul DomBus23 poate fi interfațat cu Domoticz și, utilizând mosfet-ul intern cu 30V 12A, poate regla intern luminozitatea unei benzi led.
De asemenea, DomBus23 are 2 ieșiri analogice 0-10V care permit controlul a 2 benzi de led suplimentare de către un dimmer extern cu led.

Dimming 3 led stripes with DomBus23

Conectarea DomBus23 la poarta sau deschizătorul ușii de garaj, pentru a deschide ușa porții / garajului de către Domoticz

Următoarea schemă arată cum să conectați deschizătorul de porți sau deschizătorul de uși de garaj la modulul DomBus23, care permite controlul ușii de poartă și de garaj prin sistemul de automatizare a casei (Domoticz, ...)

DomBus23 used to connect the gate and garage door opener to the home automation system

Mai multe informații la https://www.creasol.it/CreasolDomBus23




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus23

Reviews

Grade 
Tom B.

Perfect for LED dimming

I'm using it to dimmer a LED strip with domoticz.
Just connect the power supply and led strip, and it works without expensive external dimmers.

  • 1 out of 1 people found this review useful.

Write your review

Creasol DomBus23: modul Smart Home cu 2 relee, 1x mosfet, ...

Creasol DomBus23 este un modulpentru sistemul de automatizare a caseicu mai multe tipuri diferite de intrări / ieșiriîntr-o dimensiune scurtă: 74x72x24mm. p>

Poate fi conectat la controlerul Domoticz printr-o magistrală serială RS485 (4 fire, 2 pentru sursa de alimentare 12 / 24V și 2 pentru date la 115200bps).

Ca și alte dispozitive DomBus,DomBus23 este conceput pentru a consuma energie redusă, pentru a fi fiabil, complet configurabil și ușor de utilizat.

Write your review

S-ar putea sa-ti placa

Clientii care au cumparat acest produs au mai cumparat si:

Creasol DomBus23: modul...

53,68 € 37,58 €