Pilns atbalsts: lielāko daļu produktu izstrādājam mēs!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Pasūtījumi tiek nosūtīti 1 darba dienas laikā

Prioritārais pasts: ātri un lēti - Express kurjer

24 mēnešu garantija, ērta atgriešana/atmaksa

Pirms preču atgriešanas sazinieties ar mums!

Creasol DomBus23: Viedās mājas modulis ar 2x relejiem, 1x mosfet, ...

Creasol DomBus23: Viedās mājas modulis ar 2x relejiem, 1x mosfet, ...

1 Review(s) 

Creasol DomBus23 ir modulismājas automatizācijas sistēmaiar vairākām dažāda veida ieejām / izejāmīsā izmērā: 74x72x24mm. p>

To var savienot ar Domoticz kontrolieri, izmantojot RS485 sērijas kopni (4 vadi, 2 12 / 24V barošanas avotam un 2 datiem ar ātrumu 115200 b / s).

Tāpat kā citas DomBus ierīces,DomBus23 ir izstrādāts, lai patērētu maz enerģijas, būtu uzticams, pilnībā konfigurējams un viegli lietojams.

creDomBus23
Protocol: Modbus RTU (compatible with almost any system)
53,68 €
37,58 € - 30%
AR PVN Nosūtīts 1 darba dienas laikā

Apjoma atlaides

Daudzums Unit discount Cena Jūs ietaupat
1 30% 37,58 € 16,10 €
2 32% 36,50 € 34,36 €
3 34% 35,43 € 54,75 €
4 35% 34,89 € 75,15 €
6 36% 34,36 € 115,95 €
9 37% 33,82 € 178,75 €
Daudzums
Pieejams

  Pilns atbalsts: lielāko daļu produktu izstrādājam mēs!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Pasūtījumi tiek nosūtīti 1 darba dienas laikā

Prioritārais pasts: ātri un lēti - Express kurjer

  24 mēnešu garantija, ērta atgriešana/atmaksa

Pirms preču atgriešanas sazinieties ar mums!

Creasol DomBus23 ir modulismājas automatizācijas sistēmaiar vairākām dažāda veida ieejām / izejāmīsā izmērā: 74x72x24mm. p>

To var savienot ar mājas automatizācijas kontrolieri, izmantojot RS485 sērijas kopni (4 vadi, 2 12 / 24V barošanas avotam un 2 datiem ar ātrumu 115200 b / s).

Atbalstītie mājas automatizācijas sistēmas kontrolieri irDomotics.

Tāpat kā citas DomBus ierīces,DomBus23 ir izstrādāts, lai patērētu maz enerģijas, būtu uzticams, pilnībā konfigurējams un viegli lietojams.

Creasol DomBus23 smart home module for Domoticz, ...

p>

spēcīgs>

Iespējas

  • 2 SPST relejsizejas, 250Vac 5A, kuras var konfigurēt mazjaudas režīmā, lai samazinātu enerģijas patēriņu (mazāk nekā 70mW / relejs, nevis 200mW / relejs) un OUT_BLIND režīmā, lai vadītu slēģu motoru
  • 1 mosfet izeja, 30V 10A max, argan digitālās, gan dimmera funkcijas, ko var izmantot braukšanaivadīja svītru, kas regulē spilgtumu
  • 2 0-10V analogā izeja(var izmantot, lai kontrolētu citas elektroniskās plates ar 0-10 V ieeju, piemēram, dimmerus): katru no tām var konfigurēt kāatvērta kanalizācijas izeja (pieejama caur papildu vadu)ja 0-10 V analogā izeja ir bezjēdzīga
  • 2 I / OliKatru no tiem var konfigurēt kā digitālo ieeju, analogo ieeju, dubultpogu, skaitītāju (enerģijas gāzes vai ūdens skaitītājiem), digitālo izeju, žalūziju, dimmeru (savienošanai ar ārējo mosfetu) un skaņas signālu (pjezo skaņas signāls, kas savienots ar abām līnijām , push-pull konfigurācijā). li>
  • 2 zemsprieguma maiņstrāvas / līdzstrāvas optoizolācijas ieejas, 9-40V
  • 1 230 V maiņstrāvas optoizolēta ieeja
  • 7,5-35Vdc barošanas avots (iekšēji regulē komutācijas režīma barošanas ķēde, kas samazina enerģijas patēriņu un izkliedi)
  • zems enerģijas patēriņš: 10mWstāvētjauda
  • 115200 bps RS485 autobuss (maksimālais garums: 1km)

Plašāka informācija vietnē 23. https://www.creasol.it/CreasolDomBus

DomBus23 Ports iespējas

Noklusējuma adrese: 0xff23

Ostas Nr. Nosaukums Iespējas Noklusējuma konfigurācija Apraksts
1 RL1 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP SPST releja izeja ar 250Vac 5A kontakta ātrumu vai 30Vdc 5A kontakta ātrumu. Releja kontaktu varistors aizsargā no pārsprieguma
2 RL2 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP SPST releja izeja ar 250Vac 5A kontakta ātrumu vai 30Vdc 5A kontakta ātrumu. Releja kontaktu varistors aizsargā no pārsprieguma
3 MOS OUT_DIGITAL, OUT_DIMMER OUT_DIMMER Mosfet atvērta kanalizācijas izeja, 30V 12A max, piemērota vadāmu svītru kontrolei (ar iespēju regulēt spilgtumu, izmantojot DomBus aptumšošanas funkciju, 0-100% ar 5% soli) vai citām līdzstrāvas slodzēm.
4 V1 / OD1 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_ANALOG

Analogā izeja, 0-10V, piemērota citas elektroniskās plates (dimmera, siltumsūkņa, lineārā vārsta utt.) 0-10V vai 1-10V ieejas kontrolei.
Pēc izvēles šo portu ir iespējams konfigurēt kā atvērtas aizplūdes izeju 40 V 100 mA, ko var savienot ar ārējiem LED vai releju, izmantojot papildu 5 vadu kabeli:od1Šajā gadījumā pcb jumper ir jābūt īssavienotam.

5 V2 / OD2 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND(1) OUT_ANALOG OAnalog izeja, 0-10V, piemērota citas elektroniskās plates (dimmera, siltumsūkņa, lineārā vārsta utt.) 0-10V vai 1-10V ieejas kontrolei.
Pēc izvēles šo portu ir iespējams konfigurēt kā atvērtas aizplūdes izeju 40 V 100 mA, ko var savienot ar ārējiem LED vai releju, izmantojot papildu 5 vadu kabeli:od2Šajā gadījumā pcb jumper ir jābūt īssavienotam.
6 IO1 IN_DIGITAL,IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER IN_DIGITAL

Analogā / digitālā ievade, ko var izmantot sprieguma nolasīšanai, vai arī to var savienot ar kontaktu, slēdzi, magnētisko sensoru, PIR, ...
To var konfigurēt kā skaitītāju un savienot ar enerģijas / gāzes / ūdens skaitītāju.
To var konfigurēt kā IN_TWINBUTTON (ko var savienot ar dubultu spiedpogu), saīsinot PCB džemperiRU1vai 10mA OUTPUT, saīsinot PCB džemperiRO1: pēdējā gadījumā to var izmantot kā vājstrāvas 3V izeju, kas savienota ar skaņas signālu vai releja plāksni spoles draiverī.

7 IO2 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND(1), OUT_DIMMER, OUT_BUZZER IN_DIGITAL Analogā / digitālā ievade, ko var izmantot sprieguma nolasīšanai, vai arī to var savienot ar kontaktu, slēdzi, magnētisko sensoru, PIR, ...
To var konfigurēt kā skaitītāju un savienot ar enerģijas / gāzes / ūdens skaitītāju.
To var konfigurēt kā IN_TWINBUTTON (ko var savienot ar dubultu spiedpogu), saīsinot PCB džemperiRU2vai 10mA OUTPUT, saīsinot PCB džemperiRO2: pēdējā gadījumā to var izmantot kā vājstrāvas 3V izeju, kas savienota ar skaņas signālu vai releja plāksni spoles draiverī.
8 IN1 IN_AC IN_AC, IN_COUNTER Zema sprieguma ieeja, 9–40 V maiņstrāva vai līdzstrāva, optoizolēta. Piemērots, lai nojaustu klātbūtnispriegums
9 IN2 IN_AC IN_AC, IN_COUNTER Zema sprieguma ieeja, 9–40 V maiņstrāva vai līdzstrāva, optoizolēta. Piemērots sprieguma klātbūtnes noteikšanai
10 IN3 IN_AC IN_AC, IN_COUNTER 230 V ieeja, optoizolēta. Piemērots, lai noteiktu sprieguma klātbūtni un noteiktu strāvas padeves pārtraukumu (elektroenerģijas padeves pārtraukumu)

(1): var izmantot kā BLIND izeju, lai atvērtu žalūziju / aizkaru, bet tikai iepriekšējo portu var konfigurēt Domoticz kā OUT_BLIND, jo, konfigurējot kā OUT_BLIND, DomBus ierīce automātiski konfigurē nākamo portu, lai vadītu releju atvērtā stāvoklī virzienu.

Lietošanas piezīmes

1 LED svītras aptumšošana ar iekšējo Mosfet 24V 12A, + 2 LED svītras, izmantojot ārējo kontrolieri

DomBus23 modulis var būt saskarne ar Domoticz un, izmantojot iekšējo MOSFET ar 30V 12A, var iekšēji regulēt svītras spilgtumu.
Tāpat DomBus23 ir 2 analogās izejas 0-10V, kas ļauj kontrolēt 2 papildu LED svītras ar ārēju LED dimmeru.

Dimming 3 led stripes with DomBus23

DomBus23 pievienošana vārtu vai garāžu durvju atvērējam, lai Domoticz atvērtu vārtus / garāžas durvis

Šī shēma parāda, kā vārtu atvēršanu vai garāžas durvju atvērēju savienot ar DomBus23 moduli, kas ļauj kontrolēt vārtus un garāžu durvis ar mājas automatizācijas sistēmu (Domoticz, ...)

DomBus23 used to connect the gate and garage door opener to the home automation system

Plašāka informācija vietnē 23. https://www.creasol.it/CreasolDomBus




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus23

Reviews

Grade 
Tom B.

Perfect for LED dimming

I'm using it to dimmer a LED strip with domoticz.
Just connect the power supply and led strip, and it works without expensive external dimmers.

  • 1 out of 1 people found this review useful.

Write your review

Creasol DomBus23: Viedās mājas modulis ar 2x relejiem, 1x mosfet, ...

Creasol DomBus23 ir modulismājas automatizācijas sistēmaiar vairākām dažāda veida ieejām / izejāmīsā izmērā: 74x72x24mm. p>

To var savienot ar Domoticz kontrolieri, izmantojot RS485 sērijas kopni (4 vadi, 2 12 / 24V barošanas avotam un 2 datiem ar ātrumu 115200 b / s).

Tāpat kā citas DomBus ierīces,DomBus23 ir izstrādāts, lai patērētu maz enerģijas, būtu uzticams, pilnībā konfigurējams un viegli lietojams.

Write your review

Jums arī varētu patikt

Klienti, kuri iegādājās šo preci nopirka arī:

Creasol DomBus23: Viedās...

53,68 € 37,58 €