Full support: molti prodotti sono stati progettati da noi!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Gli ordini vengono spediti entro 1 giorno lavorativo

Posta prioritaria: veloce ed economica - Corriere Espresso: veloce e sicuro

24 mesi di garanzia, reso/rimborso facile

Contattaci prima di restituire i prodotti!

Creasol DomBus23: modulo Smart Home con 2x relè, 1x mosfet, ...

Creasol DomBus23: modulo Smart Home con 2x relè, 1x mosfet, ...

1 Commento(s) 

Creasol DomBus23 è un moduloper sistema domoticocon diversi tipi di ingressi / uscitein formato corto: 74x72x24mm. p>

Può essere collegato al controllo Domoticz tramite bus seriale RS485 (4 fili, 2 per alimentazione 12 / 24V e 2 per dati a 115200bps).

Come altri dispositivi DomBus,DomBus23 è progettato per consumare bassa potenza, essere affidabile, completamente configurabile e facile da usare.

creDomBus23
Protocol: Modbus RTU (compatible with almost any system)
53,68 €
37,58 € - 30%
Tasse incluse Spedizione in 1 giorno lavorativo

Sconti sul volume

Quantità Sconto unità Prezzo Salva
1 30% 37,58 € 16,10 €
2 32% 36,50 € 34,36 €
3 34% 35,43 € 54,75 €
4 35% 34,89 € 75,15 €
6 36% 34,36 € 115,95 €
9 37% 33,82 € 178,75 €
Quantità
Disponibile

  Full support: molti prodotti sono stati progettati da noi!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Gli ordini vengono spediti entro 1 giorno lavorativo

Posta prioritaria: veloce ed economica - Corriere Espresso: veloce e sicuro

  24 mesi di garanzia, reso/rimborso facile

Contattaci prima di restituire i prodotti!

Creasol DomBus23 è un moduloper sistema domoticocon diversi tipi di ingressi / uscitein formato corto: 74x72x24mm. p>

Può essere collegato al controllore domotico tramite bus seriale RS485 (4 fili, 2 per alimentazione 12 / 24V e 2 per dati a 115200bps).

I controller del sistema di automazione domestica supportati sonoDomoticz.

Come altri dispositivi DomBus,DomBus23 è progettato per consumare bassa potenza, essere affidabile, completamente configurabile e facile da usare.

Creasol DomBus23 smart home module for Domoticz, ...

p>

forte>

Caratteristiche

  • 2 relè SPSTuscite, 250Vac 5A, configurabili in modalità low power per ridurre al minimo il consumo energetico (meno di 70mW / relè, invece di 200mW / relè) e in modalità OUT_BLIND per azionare un motore per tapparelle
  • 1 uscita mosfet, 30 V 10 A max, confunzioni sia digitale che dimmer, che può essere utilizzato per guidarestriscia principale che regola la luminosità
  • 2 uscite analogiche 0-10V(può essere utilizzato per controllare altre schede elettroniche con ingresso 0-10V, come dimmer): ognuna può essere configurata comeuscita open-drain (disponibile tramite cavo opzionale)nel caso in cui l'uscita analogica 0-10V sia inutile
  • 2 I / Olines, ognuno può essere configurato come ingresso digitale, ingresso analogico, doppio pulsante, contatore (per contatori di energia gas o acqua), uscita digitale, tenda, dimmer (da collegare a mosfet esterno) e buzzer (buzzer piezoelettrico collegato alle due linee , in configurazione push-pull). li>
  • 2 ingressi optoisolati AC / DC in bassa tensione, 9-40V
  • 1 ingresso 230V AC optoisolato
  • Alimentazione 7.5-35Vdc (regolata internamente da un circuito di alimentazione switching che minimizza il consumo e la dissipazione)
  • basso consumo energetico: 10 mWpausaenergia
  • 115200 bps RS485 bus (lunghezza massima: 1 km)

Maggiori informazioni su https://www.creasol.it/CreasolDomBus23

Capacità delle porte DomBus23

Indirizzo predefinito: 0xff23

Porta# Nome Capacità Configurazione predefinita Descrizione
1 RL1 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP Uscita relè SPST, con velocità di contatto di 250 V CA 5 A o 30 V CC 5 A. Il contatto del relè è protetto dalla sovratensione tramite varistore
2 RL2 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP Uscita relè SPST, con velocità di contatto di 250 V CA 5 A o 30 V CC 5 A. Il contatto del relè è protetto dalla sovratensione tramite varistore
3 MOS OUT_DIGITAL, OUT_DIMMER OUT_DIMMER Uscita Mosfet open-drain, 30V 12A max, adatta al controllo di strisce led (con possibilità di regolare la luminosità tramite funzione dimmer DomBus, 0-100% con step 5%) o altri carichi DC.
4 V1 / OD1 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_ANALOG

Uscita analogica, 0-10V, adatta per controllare l'ingresso 0-10V o 1-10V di un'altra scheda elettronica (dimmer, pompa di calore, valvola lineare, ...).
Opzionalmente è possibile configurare questa porta come uscita open-drain 40V 100mA max, collegabile a led o relè esterni utilizzando il cavo a 5 fili opzionale:od1il ponticello del circuito stampato deve essere cortocircuitato, in questo caso.

5 V2 / OD2 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND(1) OUT_ANALOG O Uscita analogica, 0-10V, adatta per controllare l'ingresso 0-10V o 1-10V di un'altra scheda elettronica (dimmer, pompa di calore, valvola lineare, ...).
Opzionalmente è possibile configurare questa porta come uscita open-drain 40V 100mA max, collegabile a led o relè esterni utilizzando il cavo a 5 fili opzionale:od2il ponticello del circuito stampato deve essere cortocircuitato, in questo caso.
6 IO1 IN_DIGITAL,IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER IN_DIGITAL

Ingresso analogico / digitale che può essere utilizzato per leggere tensioni, oppure può essere collegato a contatto, interruttore, sensore magnetico, PIR, ...
Può essere configurato come contatore e collegato a contatore energia / gas / acqua.
Può essere configurato come IN_TWINBUTTON (collegabile ad un doppio pulsante) cortocircuitando il jumper PCBRU1o 10mA OUTPUT cortocircuitando il ponticello PCBRO1: in quest'ultimo caso può essere utilizzata come uscita 3V a bassa corrente, collegata al buzzer o ad una scheda relè all'interno del driver bobina.

7 IO2 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND(1), OUT_DIMMER, OUT_BUZZER IN_DIGITAL Ingresso analogico / digitale che può essere utilizzato per leggere tensioni, oppure può essere collegato a contatto, interruttore, sensore magnetico, PIR, ...
Può essere configurato come contatore e collegato a contatore energia / gas / acqua.
Può essere configurato come IN_TWINBUTTON (collegabile ad un doppio pulsante) cortocircuitando il jumper PCBRU2o 10mA OUTPUT cortocircuitando il ponticello PCBRO2: in quest'ultimo caso può essere utilizzata come uscita 3V a bassa corrente, collegata al buzzer o ad una scheda relè all'interno del driver bobina.
8 IN 1 IN_AC IN_AC, IN_COUNTER Ingresso a bassa tensione, 9-40 V CA o CC, optoisolato. Adatto a percepire la presenza divoltaggio
9 IN 2 IN_AC IN_AC, IN_COUNTER Ingresso a bassa tensione, 9-40 V CA o CC, optoisolato. Adatto per rilevare la presenza di tensione
10 IN3 IN_AC IN_AC, IN_COUNTER Ingresso 230V, optoisolato. Adatto per rilevare la presenza di tensione e rilevare interruzioni di corrente (blackout)

(1): può essere usata come uscita BLIND, per aprire una tenda, ma solo la porta precedente può essere configurata in Domoticz come OUT_BLIND perché, quando configurato come OUT_BLIND, il dispositivo DomBus configura automaticamente la porta successiva per pilotare un relè in aperto direzione.

Note applicative

Dimmerazione 1 striscia led tramite Mosfet interno 24V 12A, + 2 strisce led tramite controller esterno

Il modulo DomBus23 può essere interfacciato con Domoticz e, utilizzando il mosfet interno da 30V 12A, può regolare internamente la luminosità di una striscia led.
Inoltre, DomBus23 dispone di 2 uscite analogiche 0-10V che permettono di controllare 2 strisce led aggiuntive tramite un dimmer led esterno.

Dimming 3 led stripes with DomBus23

Collegamento di DomBus23 all'apriporta del cancello o del garage, per aprire il cancello / porta del garage di Domoticz

Lo schema seguente mostra come collegare l'apriporta o l'apriporta garage al modulo DomBus23, che permette di comandare cancello e porta garage tramite sistema domotico (Domoticz, ...)

DomBus23 used to connect the gate and garage door opener to the home automation system

Maggiori informazioni su https://www.creasol.it/CreasolDomBus23




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus23

Opinioni

Grado 
Tom B.

Perfect for LED dimming

I'm using it to dimmer a LED strip with domoticz.
Just connect the power supply and led strip, and it works without expensive external dimmers.

  • 1 di 1 la gente pensa che questo commento sia utile.

Scrivi la tua opinione

Creasol DomBus23: modulo Smart Home con 2x relè, 1x mosfet, ...

Creasol DomBus23 è un moduloper sistema domoticocon diversi tipi di ingressi / uscitein formato corto: 74x72x24mm. p>

Può essere collegato al controllo Domoticz tramite bus seriale RS485 (4 fili, 2 per alimentazione 12 / 24V e 2 per dati a 115200bps).

Come altri dispositivi DomBus,DomBus23 è progettato per consumare bassa potenza, essere affidabile, completamente configurabile e facile da usare.

Scrivi la tua opinione

Potrebbe anche piacerti

I clienti che hanno acquistato questo prodotto hanno comprato anche:

Creasol DomBus23: modulo...

53,68 € 37,58 €