Full support: most products are designed by us!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Bestillinger sendes innen 1 virkedag

Prioritert post: raskt og billig - Express Courier: raskt

24 måneders garanti, enkel retur/refusjon

Kontakt oss før du returnerer produkter!

Creasol DomBus23: Smart Home-modul med 2x releer, 1x mosfet, ...

Creasol DomBus23: Smart Home-modul med 2x releer, 1x mosfet, ...

1 Review(s) 

Creasol DomBus23 er en modulfor hjemmeautomatiseringssystemmed flere forskjellige slags innganger / utgangeri kort størrelse: 74x72x24mm. p>

Den kan kobles til Domoticz-kontrolleren med en RS485 seriell buss (4 ledninger, 2 for 12 / 24V strømforsyning og 2 for data ved 115200bps).

Som andre DomBus-enheter,DomBus23 er designet for å forbruke lite strøm, være pålitelig, fullt konfigurerbar og enkel å bruke.

creDomBus23
Protocol: Modbus RTU (compatible with almost any system)
€ 53.68
€ 37.58 - 30%
Inklusive MVA Sendes innen 1 virkedag

Kvantumsrabatt

Antall Enhetsrabatt Pris Du sparer
1 30% € 37.58 € 16.10
2 32% € 36.50 € 34.36
3 34% € 35.43 € 54.75
4 35% € 34.89 € 75.15
6 36% € 34.36 € 115.95
9 37% € 33.82 € 178.75
Antall
Tilgjengelig

  Full support: most products are designed by us!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Bestillinger sendes innen 1 virkedag

Prioritert post: raskt og billig - Express Courier: raskt

  24 måneders garanti, enkel retur/refusjon

Kontakt oss før du returnerer produkter!

Creasol DomBus23 er en modulfor hjemmeautomatiseringssystemmed flere forskjellige slags innganger / utgangeri kort størrelse: 74x72x24mm. p>

Den kan kobles til hjemmeautomasjonskontrolleren med en RS485 seriell buss (4 ledninger, 2 for 12 / 24V strømforsyning og 2 for data ved 115200bps).

Støttede hjemmeautomatiseringssystemkontroller erDomoticz.

Som andre DomBus-enheter,DomBus23 er designet for å forbruke lite strøm, være pålitelig, fullt konfigurerbar og enkel å bruke.

Creasol DomBus23 smart home module for Domoticz, ...

p>

sterk>

Funksjoner

  • 2 SPST-reléutganger, 250Vac 5A, som kan konfigureres i laveffektsmodus for å minimere strømforbruket (mindre enn 70mW / relé, i stedet for 200mW / relé) og i OUT_BLIND-modus for å kjøre en rulleskodermotor
  • 1 mosfet-utgang, 30V 10A maks, medbåde digitale og dimmere funksjoner, som kan brukes til å kjøreled stripe som regulerer lysstyrken
  • 2 0-10V analog utgang(kan brukes til å kontrollere andre elektroniske kort med 0-10V inngang, som dimmere): hver og en kan konfigureres somåpen avløp (tilgjengelig via den valgfrie kabelen)i tilfelle 0-10V analog utgang er ubrukelig
  • 2 I / Ulines, kan hver og en konfigureres som digital inngang, analog inngang, tvillingknapp, teller (for energigass eller vannmålere), digital utgang, persienne, dimmer (skal kobles til ekstern mosfet) og summer (piezo-summer koblet til de to linjene , i push-pull-konfigurasjon). li>
  • 2 lavspennings AC / DC opto-isolerte innganger, 9-40V
  • 1 230V vekselstrøm optisk isolert inngang
  • 7,5-35Vdc strømforsyning (internt regulert av en brytermodus strømforsyningskrets som minimerer strømforbruk og spredning)
  • lavt strømforbruk: 10mWvent littmakt
  • 115200 bps RS485 buss (maks lengde: 1km)

Mer info på https://www.creasol.it/CreasolDomBus23

DomBus23-porter

Standard adresse: 0xff23

Havn# Navn Evner Standardkonfigurasjon Beskrivelse
1 RL1 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP SPST-reléutgang, med 250Vac 5A kontakthastighet, eller 30Vdc 5A kontakthastighet. Relékontakten er beskyttet mot overspenning av varistor
2 RL2 OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_RELAY_LP SPST-reléutgang, med 250Vac 5A kontakthastighet, eller 30Vdc 5A kontakthastighet. Relékontakten er beskyttet mot overspenning av varistor
3 MOS OUT_DIGITAL, OUT_DIMMER OUT_DIMMER Mosfet utløp med åpen avløp, 30V 12A maks, egnet til å styre ledede striper (med mulighet for å regulere lysstyrken ved hjelp av DomBus-dimningsfunksjonen, 0-100% med 5% trinn) eller andre DC-belastninger.
4 V1 / OD1 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND OUT_ANALOG

Analog utgang, 0-10V, egnet til å kontrollere 0-10V eller 1-10V inngangen til et annet elektronisk kort (dimmer, varmepumpe, lineær ventil, ...).
Valgfritt er det mulig å konfigurere denne porten som åpen dreneringsutgang 40V 100mA max, som kan kobles til eksterne lysdioder eller relé ved hjelp av den valgfrie 5-ledningskabelen:od1PCB-genseren må kortsluttes, i dette tilfellet.

5 V2 / OD2 OUT_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND(1) OUT_ANALOG OAnalog utgang, 0-10V, egnet til å kontrollere 0-10V eller 1-10V inngangen til et annet elektronisk kort (dimmer, varmepumpe, lineær ventil, ...).
Valgfritt er det mulig å konfigurere denne porten som åpen dreneringsutgang 40V 100mA max, som kan kobles til eksterne lysdioder eller relé ved hjelp av den valgfrie 5-ledningskabelen:od2PCB-genseren må kortsluttes, i dette tilfellet.
6 IO1 IN_DIGITAL,IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER IN_DIGITAL

Analog / digital inngang som kan brukes til å lese spenninger, eller kan kobles til kontakt, bryter, magnetisk sensor, PIR, ...
Den kan konfigureres som teller og kobles til energi / gass / vannmåler.
Den kan konfigureres som IN_TWINBUTTON (som kan kobles til en dobbel trykknapp) ved å kortslutte PCB-jumperenRU1, eller 10mA UTGANG ved å kortslutte PCB-jumperenRO1: i sistnevnte tilfelle kan den brukes som 3V-utgang med lav strøm, koblet til summer eller til et relékort i spiraldriveren.

7 IO2 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL, OUT_BLIND(1), OUT_DIMMER, OUT_BUZZER IN_DIGITAL Analog / digital inngang som kan brukes til å lese spenninger, eller kan kobles til kontakt, bryter, magnetisk sensor, PIR, ...
Den kan konfigureres som teller og kobles til energi / gass / vannmåler.
Den kan konfigureres som IN_TWINBUTTON (som kan kobles til en dobbel trykknapp) ved å kortslutte PCB-jumperenRU2, eller 10mA UTGANG ved å kortslutte PCB-jumperenRO2: i sistnevnte tilfelle kan den brukes som 3V-utgang med lav strøm, koblet til summer eller til et relékort i spiraldriveren.
8 IN1 IN_AC IN_AC, IN_COUNTER Lavspenningsinngang, 9-40V AC eller DC, optisk isolert. Egnet for å ane nærværet avSpenning
9 IN2 IN_AC IN_AC, IN_COUNTER Lavspenningsinngang, 9-40V AC eller DC, optisk isolert. Egnet for å fornemme tilstedeværelsen av spenning
10 IN3 IN_AC IN_AC, IN_COUNTER 230V inngang, opto-isolert. Egnet for å registrere tilstedeværelsen av spenning og oppdage strømbrudd (blackout)

(1): kan brukes som BLIND-utgang, for å åpne et persienn / gardin, men bare den forrige porten kan konfigureres i Domoticz som OUT_BLIND fordi, når den er konfigurert som OUT_BLIND, konfigurerer DomBus-enheten automatisk neste port for å kjøre et relé i åpen retning.

Søknadsmerknader

Dimm 1 led stripe av interne Mosfet 24V 12A, + 2 led stripes ved bruk av ekstern kontroller

DomBus23-modulen kan være grensesnitt med Domoticz, og ved å bruke den interne mosfet med 30V 12A, kan den internt regulere lysstyrken til en led stripe.
DomBus23 har også 2 analoge utganger 0-10V som tillater å styre 2 ekstra LED-striper med en ekstern LED-dimmer.

Dimming 3 led stripes with DomBus23

Koble DomBus23 til porten eller garasjeportåpneren, for å åpne porten / garasjeporten av Domoticz

Følgende skjema viser hvordan du kobler portåpneren eller garasjeportåpneren til DomBus23-modulen, som gjør det mulig å kontrollere porten og garasjeporten med hjemmeautomatiseringssystem (Domoticz, ...)

DomBus23 used to connect the gate and garage door opener to the home automation system

Mer info på https://www.creasol.it/CreasolDomBus23




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus23

Reviews

Grade 
Tom B.

Perfect for LED dimming

I'm using it to dimmer a LED strip with domoticz.
Just connect the power supply and led strip, and it works without expensive external dimmers.

  • 1 out of 1 people found this review useful.

Write your review

Creasol DomBus23: Smart Home-modul med 2x releer, 1x mosfet, ...

Creasol DomBus23 er en modulfor hjemmeautomatiseringssystemmed flere forskjellige slags innganger / utgangeri kort størrelse: 74x72x24mm. p>

Den kan kobles til Domoticz-kontrolleren med en RS485 seriell buss (4 ledninger, 2 for 12 / 24V strømforsyning og 2 for data ved 115200bps).

Som andre DomBus-enheter,DomBus23 er designet for å forbruke lite strøm, være pålitelig, fullt konfigurerbar og enkel å bruke.

Write your review

Du liker kanskje også

Kunder som kjøpte dette produktet kjøpte også:

Creasol DomBus23: Smart...

€ 53.68 € 37.58