

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Poștă prioritară: rapid și ieftin - Curie
Contactați-ne înainte de a returna produsele!
Stație meteo care măsoară temperatura, umiditatea, presiunea, viteza vântului și direcția și ploaia. Oferta cufrumos palmacare arată toate valorile.
Palm poate fi conectat la Rasina printr-un cablu USB, deci este posibil sa obtineti si sa acumulati toate masurile pe Domoticz. Instrucțiunile de efectuare a configurației de zmeură și domoticz sunt disponibile la https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-a- domoticz
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Poștă prioritară: rapid și ieftin - Curie
Contactați-ne înainte de a returna produsele!
Stație meteo care măsoară temperatura, umiditatea, presiunea, viteza vântului și direcția și ploaia . Oferiți cu un palmier frumos care arată toate valorile.
Palm poate fi conectat la zmeură printr-un cablu USB, astfel încât este posibil să obțineți și să acumulați toate măsurile pe Domoticz . Instrucțiunile de efectuare a configurației de zmeură și domoticz sunt disponibile la https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and-a- domoticz
Stația meteo este furnizată de baterii AAA, cu o durată lungă de viață a bateriei.
Specificații:
1) Interval de temperatură exterioară: -40,0 ° C până la + 65,0 ° C (-40 ° F până la + 149 ° F)
2) Domeniul temperaturii interioare: 0 ° C până la + 50,0 ° C (32 ° F până la + 122 ° F)
3) Intervalul de umiditate: 10% până la 99% (rezoluție 1%)
4) Afișarea volumului ploii: 0 - 9999 mm (arată OFL dacă este în afara domeniului)
Rezoluție: 0,3 mm (dacă volumul de ploaie <1000 mm)
1mm (dacă volumul de ploaie> 1000mm)
5) Viteza vântului: 0 ~ 100 mph (arată OFL dacă este în afara intervalului)
6) Presiunea aerului de măsurare: 27,13inHg - 31,89inHg
Rezoluție: 0,01inHg
7) Gama de transmisie de până la 100 m (330 picioare)
8) Alimentare:
a) Palm / Receiver: 3 x baterii AA alcaline sau NiMH (nu sunt incluse)
b) stație meteorologică: 2 x baterii alcaline AA sau NiMH (nu sunt incluse)
9) Frecvența transmisiei: 433 MHz
P>
P>
P>
P>
P>
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
Raspberry... not Himbeere