

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Prioritetspost: hurtigt og billigt - Ekspresskurer: hurt
Kontakt os før returnering af produkter!
Vejrstation, der måler temperatur, fugtighed, tryk, vindhastighed og retning og regn. Leveres med aflot palmeder viser alle værdier.
Palm kan forbindes til Raspberry med et USB-kabel, så det er muligt at hente og samle alle foranstaltninger på Domoticz. Instruktioner til udførelse af hindbær og domoticz konfiguration findes på https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raberberry-pi-and- domoticz
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Prioritetspost: hurtigt og billigt - Ekspresskurer: hurt
Kontakt os før returnering af produkter!
Vejrstation, der måler temperatur, fugtighed, tryk, vindhastighed og retning og regn . Leveres med en flot palme, der viser alle værdier.
Palm kan forbindes til hindbær med et USB-kabel, så det er muligt at hente og samle alle foranstaltninger på Domoticz . Instruktioner til udførelse af hindbær og domoticz konfiguration findes på https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raberberry-pi-and- domoticz
Vejrstationen leveres af AAA batterier, med lang batterilevetid.
Specifikationer:
1) Udetemperaturområde: -40,0 ° C til + 65,0 ° C (-40 ° F til + 149 ° F)
2) Indendørs temperaturområde: 0 ° C til + 50,0 ° C (32 ° F til + 122 ° F)
3) Fugtighedsområde: 10% til 99% (1% opløsning)
4) Regnsensorvisning: 0 - 9999mm (Vis OFL hvis udvendig rækkevidde)
Opløsning: 0,3 mm (hvis regnvolumen <1000 mm)
1mm (hvis regnvolumen> 1000mm)
5) Vindhastighed: 0 ~ 100mph (Vis OFL hvis udvendig rækkevidde)
6) Måleområde lufttryk: 27,13inHg - 31,89inHg
Opløsning: 0,01inHg
7) Transmissionsområde op til 100 m (330 fod)
8) Strømforsyning:
a) Palm / Receiver: 3 x AA alkaline eller NiMH batterier (medfølger ikke)
b) Vejrstation: 2 x AA alkaline eller NiMH batterier (medfølger ikke)
9) Overførselsfrekvens: 433MHz
P>
P>
P>
P>
P>
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
Raspberry... not Himbeere