

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Courrier prioritaire : rapide et pas cher - C
Contactez-nous avant de retourner les produits !
Station météo qui mesure la température, l'humidité, la pression, la vitesse et la direction du vent et la pluie. Fournir avec unbeau palmiercela montre toutes les valeurs.
Palm peut être connecté à Raspberry par un câble USB, il est donc possible d'obtenir et d'accumuler toutes les mesures sur Domoticz. Des instructions pour effectuer la configuration de framboise et domoticz sont disponibles à l’adresse https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and- Domoticz
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Courrier prioritaire : rapide et pas cher - C
Contactez-nous avant de retourner les produits !
Station météo qui mesure la température, l'humidité, la pression, la vitesse et la direction du vent et la pluie . Fournir avec une belle paume qui montre toutes les valeurs.
Palm peut être connecté à framboise via un câble USB, il est donc possible d’obtenir et d’accumuler toutes les mesures sur Domoticz . Des instructions pour effectuer la configuration de framboise et domoticz sont disponibles à l’adresse https://www.creasol.it/support/domotics-home-automation-and-diy/128-usb-weather-station-connected-to-raspberry-pi-and- Domoticz
La station météo est alimentée par des piles AAA, avec une longue durée de vie.
Caractéristiques:
1) Plage de température extérieure: -40,0 ° C à + 65,0 ° C (-40 ° F à + 149 ° F)
2) Plage de température intérieure: 0 ° C à + 50,0 ° C (32 ° F à + 122 ° F)
3) Plage d'humidité: 10% à 99% (résolution de 1%)
4) Affichage du volume de pluie: 0 - 9999 mm (afficher OFL si en dehors de la plage)
Résolution: 0.3mm (si volume de pluie <1000mm)
1mm (si le volume de pluie> 1000mm)
5) Vitesse du vent: 0 ~ 100 mph (montre OFL si en dehors de la plage)
6) Pression atmosphérique de la plage de mesure: 27.13inHg - 31.89inHg
Résolution: 0.01inHg
7) Portée de transmission jusqu’à 100 m (330 pieds)
8) alimentation:
a) Palm / récepteur: 3 x piles alcalines AA ou NiMH (non fournies)
b) Station météo: 2 x piles alcalines AA ou NiMH (non incluses)
9) fréquence de transmission: 433 MHz
p>
p>
p>
p>
p>
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
Raspberry... not Himbeere