Volledige ondersteuning: de meeste producten zijn door ons ontworpen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Bestellingen worden binnen 1 werkdag verzonden

Priority mail: snel en goedkoop - Express Courie

24 maanden garantie, eenvoudig retourneren/restitueren

Neem contact met ons op voordat u producten retourneert!

Creasol DomBus12: 9 in- / uitgangsmodule voor Domoticz

Creasol DomBus12 - 9 I / O module voor Domoticz

0 Review(s) 

Creasol DomBus12 is een compacte module40x30x11mm,met 9 configureerbare in- / uitgangen
Het kan worden aangesloten op de Domoticz-controller via een RS485 seriële bus (4 draden, 2 voor 12 / 24V-voeding en 2 voor gegevens op 115200bps).

Net als andere DomBus-apparaten,DomBus12 is ontworpen om een laag stroomverbruik te verbruiken, betrouwbaar, volledig configureerbaar en gebruiksvriendelijk te zijn

creDomBus12
Protocol: Modbus RTU (compatible with almost any system)
€ 29,28
€ 20,50 - 30%
Inclusief belasting Verzonden in 1 werkdag

Volumekorting

Aantal Eenheidskorting Prijs U bespaart
1 30% € 20,50 € 8,78
2 32% € 19,91 € 18,74
3 34% € 19,32 € 29,87
4 35% € 19,03 € 40,99
6 36% € 18,74 € 63,24
9 37% € 18,45 € 97,50
Aantal
Beschikbaar

  Volledige ondersteuning: de meeste producten zijn door ons ontworpen!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Bestellingen worden binnen 1 werkdag verzonden

Priority mail: snel en goedkoop - Express Courie

  24 maanden garantie, eenvoudig retourneren/restitueren

Neem contact met ons op voordat u producten retourneert!

Creasol DomBus12 is een compacte module40x30x11mm,met 9 configureerbare in- / uitgangen
Het kan worden aangesloten op de Domoticz-controller via een RS485 seriële bus (4 draden, 2 voor 12 / 24V-voeding en 2 voor gegevens op 115200bps).

Net als andere DomBus-apparaten,DomBus12 is ontworpen om een laag stroomverbruik te verbruiken, betrouwbaar, volledig configureerbaar en gebruiksvriendelijk te zijn

Creasol DomBus12 module for domoticz home automation system, with 9 configurable GPIOCreasol DomBus12 - Input module for Domoticz home automation system

​/ p>

Input module for Domoticz, with 13 wires disconnectable cable

Kenmerken

  • 4 configureerbare I / Os, elk kan worden ingesteld alsanaloge / digitale ingang, ingang met twee knoppen, teller, digitale uitgang(kan worden aangesloten op externe relaiskaart in relaisstuurprogramma)
  • 2 configureerbare I / Os, elk kan worden ingesteld als open afvoer(aan te sluiten op extern relais),analoge / digitale ingangblinde uitgang(aan te sluiten op extern relais),LED strip dimmer
  • 3 conconfigureerbare I / Os, elk kan worden ingesteld alsanaloge / digitale ingangen, teller, zoemeruitgangen, blinde uitgangen(aan te sluiten op externe relaiskaart),LED strip dimmer(om te worden aangesloten op externe mosfet)
  • 7.5-35Vdc voeding (intern geregeld door een schakelende voedingsschakeling die stroomverbruik en dissipatie minimaliseert)
  • laag stroomverbruik: 0,7 mAstand-bystroom bij 12V (10mW
  • 115200 bps RS485-bus (max. Lengte: 1 km)

DomBus12 Ports-mogelijkheden

Standaardadres: 0xff12

Haven# Naam Mogelijkheden Standaard configuratie Beschrijving
1 IO IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL IN_TWINBUTTON Input, met optionele pullup (pcb-jumper)
2 IO2 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL IN_TWINBUTTON Input, met optionele pullup (pcb-jumper)
3 IO3 IN_DIGITAL, IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL IN_TWINBUTTON Input, met optionele pullup (pcb-jumper)
4 IO4 IN_DIGITAL,IN_ANALOG, IN_TWINBUTTON, IN_COUNTER, OUT_DIGITAL IN_TWINBUTTON

Input, met optionele pullup (pcb-jumper)

5 IO5 IN_DIGITAL, IN_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND, OUT_DIMMER OUT_DIGITAL Open-drain output, 60V 100mA capaciteit, geschikt om aangesloten te worden op een extern relais. Met 2 pcb jumpers is het mogelijk om mosfet te omzeilen en deze poort als normale input / output te gebruiken.
6 IO6 IN_DIGITAL, IN_ANALOG, OUT_DIGITAL, OUT_RELAY_LP, OUT_BLIND, OUT_DIMMER OUT_DIGITAL Open-drain output, 60V 100mA capaciteit, geschikt om aangesloten te worden op een extern relais. Met 2 pcb jumpers is het mogelijk om mosfet te omzeilen en deze poort als normale input / output te gebruiken.
7 IO7 IN_DIGITAL, IN_ANALOG, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER td> IN_DIGITAL Ingang, met optionele weerstand van 150 ohm die kan worden ingeschakeld door een pcb-jumper om een externe zoemer of relaiskaart in relaisstuurprogramma aan te sturen
8 IO8 IN_DIGITAL, IN_ANALOG, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER td> IN_DIGITAL Ingang, met optionele weerstand van 150 ohm die kan worden ingeschakeld door een pcb-jumper om een externe zoemer of relaiskaart in relaisstuurprogramma aan te sturen
9 IO9 IN_DIGITAL, IN_ANALOG, IN_COUNTER, OUT_DIGITAL, OUT_BLIND, OUT_DIMMER, OUT_BUZZER td> IN_DIGITAL Input, with optionele weerstand van 150 ohm die kan worden ingeschakeld door een pcb-jumper om een externe zoemer of relaiskaart in relaisstuurprogramma aan te sturen

(1): kan worden gebruikt als BLIND-uitgang, om een jaloezie / gordijn te openen, maar alleen de vorige poort kan in Domoticz worden geconfigureerd als OUT_BLIND omdat, wanneer geconfigureerd als OUT_BLIND, het DomBus-apparaat automatisch de volgende poort configureert om een relais in open richting.

Toepassingsnotities

DomBus12 gebruiken om twee 230V apparaten te besturen, met behulp van de extra module DomRelay2 (met 2 relais) h3>

Sluit gewoon de twee open-drain-uitgangen aan op de 2-relaismodule met een willekeurig type kabel (bijvoorbeeld een standaard 4x0,22mm²). p>

Deze uitgangen kunnen worden geconfigureerd als OUT_DIGITAL of, beter, als OUT_RELAY_LP: in dit geval zal het stroomverbruik van het relais 1/3 of minder zijn.

Using DomRelay2 relays module with DomBus12 to activate 230V loads

Eastron SDM230 verbinden met DomBus12 om import en export energie / stroom op Domoticz te meten

powerMetersVeel energiemeters, zoals Eastron SDM230, bieden 2 pulsuitgangen om de import en export van energie te tellen, 1 puls per Wh.

Met DomBus12, DomBus23 of DomBusTH is het heel gemakkelijk om de pulsen van energiemeters af te lezen, het onmiddellijke vermogen te berekenen en twee apparaten in Domoticz te krijgen die het u tonensalie en retourvermogen, verbruik en totale retourenergie en grafieken. Hieronder de instructies wanneer SDM230 wordt gebruikt (maar kijk in de handleiding van je energiemeter om deze aan te sluiten):

  1. verbind de pulsuitgangen met elke beschikbare I / O, bijvoorbeeld IO8 en IO9 voor DomBus12, IO1 en IO2 voor DomBusTH of DomBus23. De Het gemeenschappelijke aansluitblok van de SDM230 moet worden aangesloten op GND(0V).
  2. configureer Pulse1 output, op SDM230, als EXP kWh(raadpleeg de handleiding om te weten hoe u dat moet doen); Pulse2 is voorgeconfigureerd als IMP kWh (meet de energie geïmporteerd uit het net)
  3. configureer het Domoticz-apparaat dat is aangesloten op Pulse2: druk op Bewerken op dat apparaat en vervang in het veld Beschrijving IN_DIGITAL of IN_TWINBUTTON (de standaardwaarde) doorIN_COUNTER, TYPENAME = kWh sterk>en bespaar.Houd er rekening mee datkWhis GEVOELIG GEVAL!
    Nu wordt het apparaat automatisch verplaatst naar het Utility-paneel en geconfigureerd als energiemeter. Bewerk het opnieuw, schrijf een naam (bijvoorbeeld PowerMeter_Import) en selecteerGebruiktype.
  4. als pEnergy Power Meter Devices in Domoticzopgewekte energie moet worden gemeten, configureer het Domoticz-apparaat dat is aangesloten op Pulse1 zoals eerder: druk op Bewerken op dat apparaat en vervang in het veld Beschrijving IN_DIGITAL of IN_TWINBUTTON door
    Nu wordt het apparaat automatisch verplaatst naar het Utility-paneel en geconfigureerd als energiemeter. Bewerk het opnieuw, schrijf een naam (bijvoorbeeld PowerMeter_Export) en selecteer Return- type.
  5. In het geval dat er zowel import- als exportapparaten zijn gemaakt, is het nodig om op Importeer apparaat het unitnummer van het exportapparaat op te geven, en vice versa. Selecteer dus Instellingen -> Apparaten en noteer het Eenheidsnummer dat overeenkomt met Importeren (bijvoorbeeld 98), en Exporteer apparaat (bijvoorbeeld 99), ga dan naar het paneel Hulpprogramma, bewerk Apparaat importeren en voeg aan de beschrijving toe OPPOSITE = 99 ( Eenheid van het exportapparaat) en opslaan; bewerk Exporteer apparaat en voeg toe aan de beschrijving , OPPOSITE = 98 (Eenheid van het importapparaat) en sla op. Op deze manier wordt, wanneer een puls wordt ontvangen op het geïmporteerde apparaat, het inschakelen van het exportapparaat onmiddellijk op 0 gezet, en vice versa, wanneer een puls wordt ontvangen op het exportapparaat, wordt het inschakelen van het geïmporteerde apparaat op 0 gezet.

Domoticz heeft tot 5 minuten nodig om de energieteller correct te updaten.

Een watermeter of gasmeter aansluiten op Domoticz

Water- en gasmeter hebben doorgaans een opto-geïsoleerde uitgang die elke 0.NNN m³ een puls genereert.

Door die uitgang aan te sluiten op een I / O-ingang van DomBus12, of DomBus23 of DomBusTH, en een gemeenschappelijke uitgang op GND, is het mogelijk om een incrementele teller in Domoticz te krijgen die water, gas,en al het andere: tegendeler, meteroffset en maateenheid kunnen worden gespecificeerd in Domoticz.

Het I / O-apparaat dat op de meter is aangesloten, moet op deze manier worden geconfigureerd: klik op Bewerken op het domoticz-apparaat, schrijf de juiste naam (bijvoorbeeld Water_Meter), vervang het huidige apparaattype (bijvoorbeeld IN_DIGITAL) in het veld Beschrijving doorIN_COUNTERen opslaan: het apparaat wordt verplaatst naar het Utility-paneel en is klaar om pulsen te tellen.

Met DomBus12 module om 2x 230V belastingen aan te sturen door gebruik te maken van 2 knoppen, 4 magneetcontact sensoren en 1 PIR

Het volgende schema laat zien hoe u deze domotica-module kunt gebruiken om enkele alarmsensoren te bedienen (PIR, om bewegingen in een kamer te detecteren, en 4 magnetische contactsensoren toegepast op ramen, deuren en jaloezieën, om de open toestand en overgang te detecteren), en ook commando 2 belastingen (licht en ontvochtiger, bijvoorbeeld) door gebruik te maken van de extra DomRelay2-kaart (binnen 2 relais) geplaatst nabij de belastingen en verbonden met DomBus12 door een kleine draadkabel.

Creasol DomBus12 domoticz module that control 2 loads (220V) by 2 buttons and 5 alarm sensors

Zowel DomBus12 als DomRelay2 zijn zeer kleine modules die overal passen.

De twee knoppen zijn met elkaar verbonden door een 4k7-weerstand en verbonden met een enkele ingangsdraad: deze configuratie wordt "dubbele knop"enmaakt het mogelijk om 2 knoppen te gebruiken voor elke module-ingang, en wordt normaal gesproken gebruikt door dubbele knoppen met de functie OMHOOG / OMLAAG (bijvoorbeeld van toepassing op rolluiken) of AAN / UIT.

DomBus12, DomBus23, DomBus31 en DomBusTH hebben ook de mogelijkheid om commando's rechtstreeks naar andere apparaten te sturenvan dezelfde familie (en ook voor zichzelf), met de volgende voordelen:

  1. zeer eenvoudige configuratie(hoeft de controller niet te configureren); het is bijvoorbeeld mogelijk om een knop te configureren om een belasting te activeren, door de opdracht op de apparaatbeschrijving te schrijven zoals hieronder weergegeven
  2. tot 8 commando's worden ondersteund voor elke ingang / sensor
  3. dezecommando'szijn ontvangen enbeheerd door DomBus-modules zonder enige vertraginggeïntroduceerd door de controller
  4. commando's werken ook in het geval dat de controller niet werkt

Voorbeeld: moduleadres = 1201, met 2 knoppen aangesloten op poort 1 en geconfigureerd alsIN_TWINBUTTON, met de volgende functies:

Korte puls op de OMLAAG-knop om het licht (aangesloten op poort 6 van module 1201) 120 seconden AAN te zetten:DCMD (puls) = 1201.6: AAN: 120s

2s puls op DOWN-knop om hetzelfde licht AAN / UIT te schakelen zonder enige timer:DCMD (Pulse2) = 1201.6: WISSELEN

Korte puls op de UP-knop om de luchtontvochtiger (aangesloten op poort 5 van module 1201) 2 uur AAN te zetten:DCMD (puls) = 1201.5: AAN: 2 uur

1s pulsom de luchtontvochtiger UIT te schakelen:DCMD (Pulse1) = 1201.5: UIT

Om poort 1 van module 1201 op deze manier te configureren, is het voldoende om het poort 1-apparaat in Domoticz te bewerken en in de beschrijving alle bovenstaande commando's te schrijven:

IN_TWINBUTTON, DCMD (puls) = 1201.6: AAN: 120s, DCMD (puls2) = 1201.6: WISSELEN, DCMD (puls) = 1201.5: AAN: 2 uur, DCMD (puls1) = 1201.5: UIT

Dan werken licht en ontvochtiger ook als Domoticz offline is.

MEER INFORMATIE OPhttps://www.creasol.it/CreasolDomBus12




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus12

Reviews

Write your review

Creasol DomBus12 - 9 I / O module voor Domoticz

Creasol DomBus12 is een compacte module40x30x11mm,met 9 configureerbare in- / uitgangen
Het kan worden aangesloten op de Domoticz-controller via een RS485 seriële bus (4 draden, 2 voor 12 / 24V-voeding en 2 voor gegevens op 115200bps).

Net als andere DomBus-apparaten,DomBus12 is ontworpen om een laag stroomverbruik te verbruiken, betrouwbaar, volledig configureerbaar en gebruiksvriendelijk te zijn

Write your review

Je bent misschien ook geïnteresseerd in

Klanten die dit product aangeschaft hebben kochten ook...

Creasol DomBus12 - 9 I / O...

€ 29,28 € 20,50