

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority Mail: schnell und günstig – Exp
Kontaktieren Sie uns, bevor Sie Produkte zur
Wasserdichter NTC-Temperatursensor, 10k @25°C, 1%, B=3950
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Priority Mail: schnell und günstig – Exp
Kontaktieren Sie uns, bevor Sie Produkte zur
Wasserdichter Temperatursensor, negativer Koeffizient, mit10kWiderstand bei 25 °C,
Geeignet zur Messung der Luft- und Wasser-/Flüssigkeitstemperatur.
Kann mit einer Schraube befestigt werden und hat eine50cm langes Kabeldie mit abgeschirmtem Kabel (2x0,22mm² Kabel, normalerweise in Alarmanlagen verwendet) auf 50-100m verlängert werden kann.
Kann auch mit unserem DomBus-Set von Heimautomatisierungsmodulen verwendet werden.
Creasol DomBusTHist ein Hausautomationssystemmodul, das bereits über eine verfügtSensor für Temperatur und relative LuftfeuchtigkeitInnerhalb. Außerdem kann es an bis zu 4 externe NTC-Sensoren angeschlossen werden, um beispielsweise die Wassertemperatur am Ein- und Auslass der Wärmepumpe, die Kesselwassertemperatur, die CMV / VMC-Lufttemperatur oder andere Raumtemperaturen zu messen. Lesen Sie den folgenden Abschnitt, um zu erfahren, wie das DomBus-Modul für die Verwendung dieser Art von Sensor konfiguriert wird.
Creasol DomBus12, genauso wie andere DomBus-ModuleDomBusTH,DomBus23,DomBus32,DomBus34, ..., hat einige analoge Eingänge innerhalb von 10k Pullup-Widerständen tHut angeschlossen werden kannNTC-Thermistoren zur Temperaturmessung, mit NTC 10k mit 3950 B Koeffizient.
NTC-Sensoren sind wasserdicht, mit 2-adrigem Kabel, das mit einem gemeinsamen Alarmkabel 2x0,22 mm² + Abschirmung auf 50-100 m verlängert werden kann; Mit einem einzigen 4x0,22mm²+Schirmkabel können 4 verschiedene Temperatursensoren angeschlossen werden.
Das Diagramm unten zeigtDomBus12Modul mit 4 an IO1-4 angeschlossenen Temperatursensoren, ein Remote-DoppelrelaismodulDomRelais2an IO5-6 und 2 Taster an IO8-9 angeschlossen.
Das an den NTC-Temperatursensor angeschlossene E/A-Gerät sollte in Domoticz wie folgt konfiguriert werdenIN_ANALOG,FUNKTION=3950Außerdem ist es möglich, einen Offset hinzuzufügen, um beispielsweise Temperaturfehler zu kompensierenIN_ANALOG,FUNKTION=3950,B=0,2 wenn die tatsächliche Temperatur 0,2 °C über der gemessenen Temperatur liegt.
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller