

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Posta prioritaria: veloce ed economica - Corriere Espresso: veloce e sicuro
Contattaci prima di restituire i prodotti!
Sensore di temperatura NTC impermeabile, 10k @25°C, 1%, B=3950
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Posta prioritaria: veloce ed economica - Corriere Espresso: veloce e sicuro
Contattaci prima di restituire i prodotti!
Sensore di temperatura impermeabile, coefficiente negativo, con10kresistenza a 25 °C,
Adatto per misurare la temperatura dell'aria e dell'acqua/fluido.
Può essere fissato con una vite e ha unCavo lungo 50 cmche può essere esteso fino a 50-100m utilizzando cavo schermato (cavo 2x0.22mm², normalmente utilizzato nei sistemi di allarme).
Utilizzabile anche con il nostro set di moduli domotici DomBus.
Creasol DomBusTHè un modulo del sistema domotico che dispone già di unsensore di temperatura e umidità relativadentro. Inoltre, può essere collegato a un massimo di 4 sensori NTC esterni per misurare, ad esempio, la temperatura dell'acqua in ingresso e in uscita della pompa di calore, la temperatura dell'acqua della caldaia, la temperatura dell'aria CMV/VMC o altre temperature ambiente. Vedere la sezione seguente per sapere come configurare il modulo DomBus per utilizzare questo tipo di sensore.
Creasol DomBus12, come gli altri moduli DomBusDomBusTH,DomBus23,DomBus32,DomBus34, ..., ha alcuni ingressi analogici all'interno di resistori di pullup da 10k tcappello può essere collegato aTermistori NTC per la misura della temperatura, utilizzando NTC 10k con coefficiente 3950 B.
I sensori NTC sono stagni, con cavo a 2 fili che può essere esteso per 50-100m di distanza utilizzando un comune cavo di allarme 2x0.22mm² + schermatura; utilizzando un unico cavo 4x0.22mm²+schermato è possibile collegare 4 diversi sensori di temperatura.
Lo schema seguente mostraDomBus12modulo con 4 sensori di temperatura collegati su IO1-4, un modulo doppio relè remotoDomRelay2collegato a IO5-6 e 2 pulsanti a IO8-9.
Il dispositivo I/O collegato al sensore di temperatura NTC deve essere configurato, in Domoticz, comeIN_ANALOGICO,FUNZIONE=3950ed è inoltre possibile aggiungere un offset per compensare eventuali errori di temperatura, ad esempioIN_ANALOGICO,FUNZIONE=3950,B=0.2 se la temperatura reale è di 0,2°C superiore alla temperatura misurata.
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller