Creasol DomBus33 - Módulo Domoticz con 3 relés, 3 entradas CA, 5 E/S para sistemas de iluminación existentes
0 Comentario(s) 
Módulo en carril DIN diseñado para domotizar 3 luminarias existentes mediante pulsador de 230V y relé paso a paso. El relé se usa para alternar el relé paso a paso externo (enviando un pulso a su bobina de 230 V) y la entrada de CA se usa para monitorear el estado de la luz (encendido/apagado). Las 5 E/S analógicas/digitales se pueden conectar a pulsadores de baja tensión, contadores, distancia de temperatura y sensores de alarma.
Soporte completo: ¡la mayoría de los productos están diseñados por nosotros!
DomBus33 es unMódulo CARRIL DIN, 54mm de ancho,con3 salidas de relé,3 entradas de CAy5 E/S de bajo voltajedisponible con dos firmwares diferentes:
Protocolo propietario DomBus, utilizable con Domoticz: integra DCMD (comandos enviados al mismo u otros módulos cuando cambia una entrada/sensor, como KNX)
Protocolo estándar Modbus, utilizable con Home Assistant, OpenHAB, Node-RED, ...
DomBus33 tiene el mismo hardware queDomBus32pero con firmware diseñado específicamente para controlar/monitorizar las luces: de esta forma, la luz puede activarse mediante los pulsadores de 230 V existentes (que envían pulsos a la bobina del relé de paso), y también mediante el controlador domótico (escenas, grupos, apagar todas las luces al salir del edificio, controlar la luz con el teléfono inteligente, activar las luces aleatoriamente cuando el sistema de alarma está en modo AWAY, ...).
Para simplificar el cableado, el bloque de terminales tiene 3 terminales para relés, 3 para entradas de CA y 1 terminal común (para conectarse a Neutro o Línea): de esta manera es más fácil y rápido conectar the módulo para cargas eléctricas que comparten el mismo disyuntor (por ejemplo, sistema de iluminación, válvulas del sistema de calefacción, ...). por favor tenga cuidado deconecte solo cargas que estén protegidas por el mismo RCCB (disyuntor). Por supuesto, es posible utilizar relés para conmutar cargas de baja tensión o seleccionar el modo de funcionamiento de una máquina (bomba de calor, por ejemplo), conectando la línea común a GND o tensión de alimentación de CC: en este caso, las 3 entradas de CA son inútiles.
Como otros módulos DomBus,todos los puertos se pueden configurar de muchas maneras diferentes, y también este móduloadmite DCMD, comandos enviados al mismo u otros módulos DomBusrealizar acciones sencillas, que permitan alcanzar una alta fiabilidad (Los comandos DCMD funcionan incluso si el controlador domótico no está operativo) y fácil programación (no es necesario crear automatizaciones en el controlador domótico: simplemente configure los puertos DomBus para realizar acciones en los eventos). Por último, pero no menos importante, como otros módulos DomBus, DomBus33 esoptimizado para obtener un bajo consumo de energía, menos de 10 mW normalmente (0,75 mA a 13,6 V) y menos de 150 mW cuando los 3 relés están encendidos (10 mA a 13,6 V).
Características
3 salidas de relé, 250Vac 5A max, con protección contra sobretensiones (varistores)
3 entradas de CA, 110-230 V, para monitorear el voltaje en las cargas
1 bloque de terminales común (para Neutro, Línea o voltaje común), para simplificar las conexiones
5 E/S programables
Fuente de alimentación 8-25Vdc
Consumo de energía de 10 mW
Consumo de energía máximo de 150 mW
52x89x65mm
Aplicaciones
Encender/apagar hasta 3 luces u otras cargas
Comprobar que los aparatos estén alimentados (por ejemplo, comprobar que la bomba de calor esté correctamente alimentada durante el invierno, para evitar que el circuito hidráulico se rompa durante el invierno cuando la temperatura desciende por debajo de 0°C)
Activar/desactivar las válvulas del sistema de calefacción
Conecte hasta 5 PIR, sensores de contacto magnético u otros dispositivos de bajo voltaje.
Interconecta hasta 3 PIR con salida de 230 V para habilitar luces externas y comenzar a grabar (NVR o DVR)
....
Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
very low power (around 10mW with relays OFF)
reliable (no disconnections)
bus connected (no radiofrequency interference, no battery to replace).
Modules are available in two version:
with DomBus proprietary protocol, working with Domoticz only
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Single-phase and three-phases, up to 36A (8kW or 22kW)
Needs external contactor, RCCB (protection) and EV cable
Optional power meter to measure charging power, energy, voltage and power factor
Optional power meter to measure the power usage from the grid (not needed if already exists)
Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)
DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
temperature and relative humidity sensor
red, green and white LEDs
4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.
DomBus12 - Compact domotic module with 9 I/Os
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
analog/digital inputs
pushbutton and UP/DOWN pushbutton
counters (water, gas, S0 energy, ...)
NTC temperature and ultrasonic distance sensors
2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.
DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
3x high power latching relays SPST 15A: latching relay consumes nothing when ON
1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...
DomBus23 - Domotic module with many functions
Versatile module designed to control gate or garage door.
2x relays SPST 5A
1x 10A 30V mosfet (led stripe dimming)
2x 0-10V analog output: each one can be configured as open-drain output to control external relay
DIN rail low profile module, with 8 relays and very low power consumption:
6x relays SPST 5A
2x relays STDT 10A
Only 10mW power consumption with all relays OFF
Only 500mW power consumption with all 8 relays ON !!
DomBus32 - Domotic module with 3 relays
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
DomBus33 - Module to domotize a light system using step relays
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
3x relays SPST 5A
3x 115/230Vac optoisolated inputs
Single common for relays and AC inputs
5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DomBus36 - Domotic module with 12 relays
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
12x relays SPST 5A
Relays are grouped in 3 blocks, with a single common per block, for easier wiring
Only 12mW power consumption with all relays OFF
Only 750mW power consumption with all 12 relays ON !!
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
3x 115/230Vac optoisolated inputs
2x relays SPST 5A
1x relay SPST 10A
DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs
DIN rail module designed for burglar alarm system.
4x relays SPDT (normally open + close contacts), 10A
2x relays SPST 10A
1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
Works in stand-alone mode (no need for external controller)
Can be connected to Domoticz for monitoring and controlling the motors position
DomRelay2 - 2x relays board
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
2x 5A 12V SPST relays (Normally Open contact)
Overvoltage protection (for inductive loads, like motors)
Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)
DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller
9-24V input voltage, with high efficiency DC/DC regulator with 5V output
4x SPST relays 5V with overvoltage protection
1x SSR output (max 40V output)
2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
1x I²C interface for sensors, extended I/Os and more)
1x OneWire interface (DS18B20 or other 1wire sensors/devices)
Módulo en carril DIN diseñado para domotizar 3 luminarias existentes mediante pulsador de 230V y relé paso a paso. El relé se usa para alternar el relé paso a paso externo (enviando un pulso a su bobina de 230 V) y la entrada de CA se usa para monitorear el estado de la luz (encendido/apagado). Las 5 E/S analógicas/digitales se pueden conectar a pulsadores de baja tensión, contadores, distancia de temperatura y sensores de alarma.