Suporte total: a maioria dos produtos são projetados por nós!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

Os pedidos são enviados em até 1 dia útil

Correio prioritário: rápido e barato - Express Courie

24 meses de garantia, fácil devolução/reembolso

Contate-nos antes de devolver produtos!

Creasol DomBus38: 6 relés + 1 entrada CA + 12 entradas

Creasol DomBus38: 6 relés + 1 entrada CA + 12 entradas

0 Review(s) 

Módulo de automação residencial de alta confiabilidade e baixo consumo de energia em trilho DIN com saída de relés, entradas de baixa tensão e uma entrada de 100-250 Vca. Funciona com sistemas de automação residencial como Domótica, Assistente doméstico, Node-RED, OpenHAB e mais...

Pode ser usado para gerenciar sensores de alarme, botões de pressão, luzes e outras cargas e monitorar a presença de 230 V (detectando queda de energia).

creDomBus38
Protocol: Modbus RTU (compatible with almost any system)
95,16 €
66,61 € - 30%
Com IVA Enviado em 1 dia útil
Quantidade
Disponível

  Suporte total: a maioria dos produtos são projetados por nós!

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010

  Os pedidos são enviados em até 1 dia útil

Correio prioritário: rápido e barato - Express Courie

  24 meses de garantia, fácil devolução/reembolso

Contate-nos antes de devolver produtos!

domotic module with 6 relays, 1 AC input, 12 low voltage inputs

Pode ser conectado ao controlador de automação residencial por um barramento serial RS485 (4 fios, 2 para alimentação de 12/24 V e 2 para dados a 115200 bps).

Como outros dispositivos DomBus, O DomBus38 foi projetado para consumir pouca energia, ser confiável, totalmente configurável e fácil de usar.


Características

  • 4 relés de 10A com saídas normalmente abertas e normalmente fechadas no bloco de terminais, configurado no modo de baixo consumo (cerca de 100 mW/cada, quando ligado)
  • 2x relés 10A com saídas normalmente abertas, configuradas em modo de baixa potência (cerca de 100 mW/cada, quando ligado)
  • 1x entrada optoisolada CA para detectar (e notificar) falta de energia, implementando detecção de cruzamento zero para permitir a comutação de relés minimizando a corrente de pico (para cargas capacitivas, como placas eletrônicas) e a sobretensão (para corrente indutiva, como motores e bobinas).
  • 10x entradas de baixa tensão com pullup de 10k resistor que pode ser habilitado por jumper de PCB: pode ser conectado a botões de pressão, interruptores, botões duplos (botão para cima/para baixo conectado a uma única entrada), sensores de alarme (contato magnético, PIR, ...), contadores e medidores com saída pulsada, sensores de temperatura NTC, ...
  • 2x entradas de baixa tensão com pullup interno resistor que pode ser excluído em caso de entradas analógicas: pode ser conectado a botões de pressão, interruptores, sensores de alarme (contato magnético, PIR, ...), contadores e medidores com saída pulsada, tensões analógicas na faixa de 0÷3,3V.

    li>
  • Resistor de terminação de barramento RS485 interno (150 ohm) que pode ser ativado por um jumper de PCB (com um ferro de solda)
  • Barramento industrial RS485, que funciona com até 500m de cabo (usando cabo de alarme padrão: 2x0,50+2x0,22mm² + blindagem)/li>
  • Gabinete de perfil baixo para trilho DIN, 115x90x40mm, 220g
  • Blocos de terminais de plug-in (desconectável) para fiação fácil
  • Disponível com 2 firmwares de sua escolha:
    • Firmware DomBus, trabalhando com Domoticz, implementando o protocolo proprietário DomBus
    • Firmware Modbus, trabalhando com NodeRED, Home Assistant, OpenHAB e muitos outros controladores que suportam o protocolo padrão Modbus.
  • Consumo de energia muito baixo: 15mW com relés DESLIGADOS.

Avisos

  • Não misture dispositivos de alta e baixa tensão em blocos de saída de relé: os relés podem ser usados todos conectados a dispositivos de 115/230 Vca, ou todos conectados a dispositivos de 30 Vmáx dentro do mesmo bloco. Por exemplo, se RL1 estiver conectado a 230 V, RL2÷RL4 pode ser conectado somente a cargas de 230 V, e dispositivos de baixa tensão podem ser cconectado somente a RL5÷RL6, ou vice-versa. Claro, é possível conectar todos os RL1÷RL6 a alta tensão OU cargas de baixa tensão.
  • Use um Cabo blindado de 4 fios para o barramento, usando duas linhas para alimentar alimentação (12 ou 24Vdc) protegida por fusível.
  • Para reduzir o ruído e os reflexos no ônibus, habilitar o resistor de terminação (curto-circuito no jumper do PCB Rbus atrás do LED) nas duas extremidades mais distantes do ônibus.

Informações completas disponíveis na página em inglês https://www.creasol.it/DomBus38




Smart-Home Creasol DomBus modules for Domoticz, Home Assistant, Node-RED, OpenHAB, ...

The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.


The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.

Our industrial and home automation modules are designed to be

  • very low power (around 10mW with relays OFF)
  • reliable (no disconnections)
  • bus connected (no radiofrequency interference, no battery to replace).

Modules are available in two version:

  1. with DomBus proprietary protocol, working with Domoticz only
  2. with Modbus standard protocol, working with Home Assistant, OpenHAB, Node-RED
Home automation system using DomBus modules

Store website - Information website

For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram

DomBusEVSE - EVSE module to build a Smart Wallbox / EV charging station

DomBusEVSE smart EVSE module to make a Smart Wallbox EV Charging station Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.

  • Single-phase and three-phases, up to 36A (8kW or 22kW)
  • Needs external contactor, RCCB (protection) and EV cable
  • Optional power meter to measure charging power, energy, voltage and power factor
  • Optional power meter to measure the power usage from the grid (not needed if already exists)
  • Two max grid power thresholds can be programmed: for example, in Italy who have 6kW contractual power can drain from the grid Max (6* 1.27)=7.6kW for max 90 minutes followed by (6* 1.1)=6.6kW for another 90 minutes. The module can use ALL available power when programmed to charge at 100%.
  • Works without the domotic controller (stand-alone mode), and can also work with charging current set by the domotic controller (managed mode)

DomBusTH - Compact board to be placed on a blank cover, with temperature and humidity sensor and RGW LEDs

DomBusTH domotic board with temperature and humidity sensor, 3 LEDs, 6 I/O Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.

Includes:

  • temperature and relative humidity sensor
  • red, green and white LEDs
  • 4 I/Os configurable as analog or digital inputs, pushbuttons, counters (water, gas, S0 energy, ...), NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays; they can also be configured as analog/digital inputs, pushbuttons and distance sensors.

DomBus12 - Compact domotic module with 9 I/Os

DomBus12 domotic module with 9 I/O Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:

  • analog/digital inputs
  • pushbutton and UP/DOWN pushbutton
  • counters (water, gas, S0 energy, ...)
  • NTC temperature and ultrasonic distance sensors
  • 2 ports are configured by default as open-drain output and can drive up to 200mA led strip (with dimming function) or can be connected to the external module DomRelay2 to control 2 relays.

DomBus21 - Power optimized module with 3 High Power latching relays, 1 AC input and 4 low voltage inputs

DomBus21 module with 3 high power latching relays Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).

  • 3x high power latching relays SPST 15A: latching relay consumes nothing when ON
  • 1x 230V AC opto-isolated input used as power outage detector, and also as zero-crossing detector to permit switching relays On/Off minimizing in-rush current (for capacitive loads) and overvoltage (for inductive loads)
  • 4x low voltage inputs, that can be connected to pushbuttons, switches, meters with pulsed output, NTC temperature sensors, ...

DomBus23 - Domotic module with many functions

DomBus23 domotic module with many functions Versatile module designed to control gate or garage door.

  • 2x relays SPST 5A
  • 1x 10A 30V mosfet (led stripe dimming)
  • 2x 0-10V analog output: each one can be configured as open-drain output to control external relay
  • 2x I/O lines, configurable as analog/digital inputs, temperature/distance sensor, counter, ...
  • 2x low voltage AC/DC opto-isolated inputs, 9-40V
  • 1x 230V AC opto-isolated input

DomBus31 - Domotic module with 8 relays

DomBus31 domotic module with 8 relay outputs DIN rail low profile module, with 8 relays and very low power consumption:

  • 6x relays SPST 5A
  • 2x relays STDT 10A
  • Only 10mW power consumption with all relays OFF
  • Only 500mW power consumption with all 8 relays ON !!

DomBus32 - Domotic module with 3 relays

DomBus32 domotic module with 3 relay outputs Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

DomBus33 - Module to domotize a light system using step relays

DomBus33 domotic module with 3 relay outputs that can control 3 lights Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.

  • 3x relays SPST 5A
  • 3x 115/230Vac optoisolated inputs
  • Single common for relays and AC inputs
  • 5x general purpose I/O, each one configurable as analog/digital inputs, pushbutton, counter, temperature and distance sensor.

Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.

DomBus36 - Domotic module with 12 relays

DomBus36 domotic module with 12 relay outputs DIN rail module, low profile, with 12 relays outputs and very low power consumption.

  • 12x relays SPST 5A
  • Relays are grouped in 3 blocks, with a single common per block, for easier wiring
  • Only 12mW power consumption with all relays OFF
  • Only 750mW power consumption with all 12 relays ON !!

DomBus37 - 12 inputs, 3 115/230Vac inputs, 3 relay outputs

DomBus37 domotic module with 12 inputs, 3 AC inputs, 3 relay outputs Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.

  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)
  • 3x 115/230Vac optoisolated inputs
  • 2x relays SPST 5A
  • 1x relay SPST 10A

DomBus38 - 4 SPDT 10A relays, 2 SPST 10A relays, 1 AC input, 12 low voltage inputs

DomBus38 domotic module with 12 inputs, 1 AC input, 6 relay outputs DIN rail module designed for burglar alarm system.

  • 4x relays SPDT (normally open + close contacts), 10A
  • 2x relays SPST 10A
  • 1x 115/230Vac optoisolated inputs, that can be used to monitor 230V voltage presence (blackout detector) and it's also used as zero-crossing detector to minimize in-rush current and overvoltage when a relay switches On/Off
  • 12x low voltage inputs (analog/digital inputs, buttons, alarm sensors, balanced double/triple biased alarm sensors, counters, temperature and distance sensors, ...)

DomBusTracker - Smart dual-axis sun tracker to optimize photovoltaic production

DomBusTracker domotic module that controls a dual-axis solar tracker motors DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.

  • Uses a deep-hole sun sensor, to optimize production with both sunny and cloudy weather
  • Works in stand-alone mode (no need for external controller)
  • Can be connected to Domoticz for monitoring and controlling the motors position

DomRelay2 - 2x relays board

Relay board with 2 relays, to be used with DomBus domotic modules Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs

  • 2x 5A 12V SPST relays (Normally Open contact)
  • Overvoltage protection (for inductive loads, like motors)
  • Overcurrent protection (for capacitive laods, like AC/DC power supply, LED bulbs, ...)

DomESP1 / DomESP2 - Board with relays and more for ESP8266 NodeMCU WiFi module

Relay board for ESP8266 NodeMCU module IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller

  • 9-24V input voltage, with high efficiency DC/DC regulator with 5V output
  • 4x SPST relays 5V with overvoltage protection
  • 1x SSR output (max 40V output)
  • 2x mosfet output (max 30V, 10A) for LED dimming or other DC loads
  • 1x I²C interface for sensors, extended I/Os and more)
  • 1x OneWire interface (DS18B20 or other 1wire sensors/devices)

creDomBus38

Reviews

Write your review

Creasol DomBus38: 6 relés + 1 entrada CA + 12 entradas

Módulo de automação residencial de alta confiabilidade e baixo consumo de energia em trilho DIN com saída de relés, entradas de baixa tensão e uma entrada de 100-250 Vca. Funciona com sistemas de automação residencial como Domótica, Assistente doméstico, Node-RED, OpenHAB e mais...

Pode ser usado para gerenciar sensores de alarme, botões de pressão, luzes e outras cargas e monitorar a presença de 230 V (detectando queda de energia).

Write your review

Também poderá gostar

Creasol DomBus38: 6 relés +...

95,16 € 66,61 €