

Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Elsőbbségi posta: gyors és olcsó - Expressz f
A termékek visszaküldése előtt vegye fel velünk a kapcsolatot!
Email: store@creasol.it - Telegram: CreasolTech - Whatsapp: +393283730010
Elsőbbségi posta: gyors és olcsó - Expressz f
A termékek visszaküldése előtt vegye fel velünk a kapcsolatot!
A Raspberry Pi több millió példányban kelt el világszerte a 2012-es első megjelenése óta, és még mindig nagyon népszerű. Mert sok Raspberry Pi felhasználónak nem csak egy fedélzeti számítógépe van otthon, hanem részben 4-5 darab.
Az egyik HD médialejátszóként működik külső merevlemezzel házimozihoz vagy kijelzős internetes rádióként, a másik webkamera-szerverként kamerás megfigyeléshez, élő közvetítéssel a mobiltelefonra, a másik pedig otthoni automatizáláshoz, például fűtéshez vagy világításhoz. vezérlőt, egy másikat pedig egyszerű WLAN-nyomtatószerverként vagy miniszámítógépként az általános internetezéshez, hogy csak néhány alkalmazási esetet említsünk.
Észreveheti, hogy a kis "minden mesterség" nem csak sok mindenre képes, de rendkívül olcsó is, ami miatt olyan vonzó. Csak a programozási hajlandóságot érdemes magunkkal hozni, és még azt sem, mert egyszerűen átprogramozhatunk fórumokból vagy könyvekből származó instrukciók szerint, vagy kényelmesen telepíthetünk kész képet a Raspberry Pi-re - merj!
Mi újdonság a Raspberry Pi 4 B-n?
Régi Raspberry Pi 3 B+- 1,4 GHz-es ARM Cortex-A53 négymagos CPU
- 1 GB LPDDR2 SDRAM
- Gigabit LAN RJ45 (USB 2.0-n keresztül, akár 300 Mbit)
- Bluetooth 4.2
- 4x USB 2.0
- 1x HDMI (1080p @ 60 fps) H.264
- 5V/2.5A @ microUSB
Új Raspberry Pi 4 B- 1,5 GHz-es ARM Cortex-A72 négymagos CPU
- 2 GB vagy 4 GB LPDDR4 SDRAM
- Gigabit LAN RJ45 (akár 1000 Mbit)
- Bluetooth 5.0
- 2x USB 2.0 / 2x USB 3.0
- 2x microHDMI (1x 4k @60fps vagy 2x4k @30fps) H.265/H.264
- 5V/3A @ USB Type-C
A következő 3 különböző változat létezik-
- Raspberry Pi 4 B 2 GB 2 GB RAM-mal
- Raspberry Pi 4 B 4 GB 4 GB RAM-mal
- Raspberry Pi 4 B 8 GB 8 GB RAM-mal
Fontos jegyzetAz egyéb csatlakozások miatt, például 1x HDMI helyett 2x microHDMI és microUSB helyett USB Type-C, de a LAN port és USB port cseréje miatt is új házak szükségesek (lásd a tartozékokat). Az alaplaphoz ezentúl legalább 5V/3A-es C típusú USB-csatlakozós tápra is szükség van (lásd a tartozékokat), és már nem 5V/2,5A-es microUSB tápegységet. Egyébként a meglévő tartozékok teljes mértékben kompatibilisek az új Raspberry Pi-vel.
Tippek:- A teljes funkcionalitás érdekében a legújabb szoftverre van szüksége, amely elérhető a www.raspberrypi.org oldalon vagy online boltunkban.
- az USB-C porttal kapcsolatos esetleges problémák elkerülése érdekében javasolt az eredeti vagy azzal egyenértékű tápegység használata.
The following video shows a presentation of some domotic modules designed and produced in Italy by Creasol to make a reliable, easy and power-optimized home automation system.
The next video shows our Smart EVSE module that can be used to charge the electric car by using only solar power, or adding 25/50/75/100% of available power from the electrical grid.
Our industrial and home automation modules are designed to be
Modules are available in two version:
Store website - Information website
For our products we can offer FULL SUPPORT and CUSTOMIZATION: please contact us by Email or Telegram
Complete solution to make a Smart EVSE, charging the electric vehicle using only energy from renewable source (photovoltaic, wind, ...), or adding 25-50-75-100% of available power from the grid.
Compact board, 32x17mm, to be installed on blank cover with a 4mm hole in the middle, to exchange air for the relative humidity sensor. It can be installed in every room to monitor temperature and humidity, check alarm sensors, control blind motor UP/DOWN, send notifications (using red and green leds) and activate white led in case of power outage.
Includes:
Very compact, versatile and cost-effective module with 9 ports. Each port can be configured by software as:
Very low power consumption module designed to enable up to 3 high power loads, up to 15A (3kW).
Versatile module designed to control gate or garage door.
DIN rail low profile module, with 8 relays and very low power consumption:
Versatile module with 230V inputs and outputs, and 5 low voltage I/Os.
Module designed to control 3 lights already existing and actually controlled by 230V pushbuttons and step-by-step relays. In this way each light can be activated by existing pushbuttons, and by the domotic controller.
Each relay can toggle the existing step-relay, switching the light On/Off. The optoisolator monitors the light status. The 5 I/Os can be connected to pushbuttons to activate or deactivate one or all lights.
DIN rail module, low profile, with 12 relays outputs and very low power consumption.
Module designed to be connected to alarm sensors (magnetc contact sensors, PIRs, tampers): it's able to monitor mains power supply (power outage / blackout) and also have 3 relays outputs.
DIN rail module designed for burglar alarm system.
DIN rail module that control azimuth + elevation/tilt motors of a sun tracker, to maximize photovoltaic energy production during the day and seasons.
Simple module with 2 relays, to be used with DomBus modules or other electronic boards with open-collector or open-drain outputs
IoT board designed for NodeMCU v3 board using ESP8266 WiFi microcontroller